Jump to content
MSW Spring Donation Drive

BANYAN

SPECIAL CONTRIBUTOR
 View Profile  See their activity

  • Posts

    5,537

  • Joined

  • Last visited

 Content Type 

Everything posted by BANYAN

  1. BANYAN
    AKRYPTO, try the RAAF Museum at Point Cook, I think they have a Walrus. An email may elicit a response or some answers? cheers Pat
  2. BANYAN
    Absolutely stunning detail Brian; looks great! Don't worry about the desk, there is plenty of eye candy to distract from that cheers Pat
  3. BANYAN
    That's looking pretty good. cheers Pat
  4. BANYAN
    Eberhard, with this machine it is even more important to get it set-up right. It works really well to make LH lay, but to do RH, the feed spools need to be wound differently, and if you do not use the correct initial lay of the stock thread, it twists and kinks madly as it is made up. It can be done, but it takes a LOT of patience and a lot of fussing about (in my experience, and also experienced by a couple of others in earlier discussions in this forum). The machine is beautifully made and a credit to Jim (as with his other machine tools), it is just a lot more complicated to set-up and use to make RH laid rope which sort of detracts from it other primary features (being able to produce long lengths of rope) in a minimal foot print (only a couple hundred mm). I will report back after I have experimented further with it as I think I have found some LH laid stock BUIT much too big for my purposes - unfortunately everything in the Victoria is RH laid (as she has wirerope instead of cable laid shrouds and other standing rigging). cheers Pat
  5. BANYAN
    Both Keith I have one of Jim Byrne's Universal ropewalks which is very good at left hand lay but not so easy to make RH lay - need to source LH thread stock and a bit of mucking around. This may be due to the fact I do not use it that often and have not yet developed the technique adequately for RH. For RH I have been using the club's walking rope maker which, with a bit of techniques allows some very fine small scale (down to .25 so far) ropes to be made. I am confident I can get 0.2mm but not sure about 0.1mm - If I can find suitably coloured fly tying thread/line as suggested by Eberhard, I will have a go with that. The stuff I have used though is easily frayed so will have to experiment with make as well. cheers Pat
  6. BANYAN
    Nice find Bruce; thanks for sharing. I wish they would fold out those illustrations when copying cheers Pat
  7. BANYAN
    Hi Keith, thanks for the suggestion. I have tried polyester, and still experimenting with Rayon, but I found the poly has just too much stretch in it - even PR stretching hasn't helped much, especially here with the wide range of humidity we experience. I agree with you re shine though, especially if you use the 'glace' types. cheers Pat
  8. BANYAN
    Bruce, sorry for my tardiness; had not realised you had started a log. A very interesting discussion of your progress, trials and tribulations and it seems you have conquered all. Looking forward to your updates. cheers Pat
  9. BANYAN
    Very nice work Steven, your persistence to get it right is 'Admir'able - sorry couldn't resist. Seriously, though, your GH is looking great and I really love those sails. cheers Pat
  10. BANYAN
    Love the detail you are adding Glen, quite the diorama! cheers Pat
  11. BANYAN
    Stunning detail and very well executed Greg; some great eye candy. cheers Pat
  12. BANYAN
    Thanks for the feedback and comments Eberhard and Mark, and for all the 'likes'. Eberhard, yep, hopefully I will be able to make all of it, but may resort to suitable thread if I have no luck with the smaller stuff. I'll have a close look at that fly tying thread, but my concern here would be a colour match with the thread I have found for the silver/grey to simulate wire - this latter is a Gutterman cotton (long staple). cheers Pat
  13. BANYAN
    Ditto Looking really good Rob, the furled sails really add to the look, and I am seriously considering this for the Victoria. cheers Pat
  14. BANYAN
    Hi folks, this post is one for those interested in just how much scale rope would be required to fully rig a vessel in the mid-19th century (steam/sail). HMCSS Victoria was rigged as a three masted Barque with a full outfit of fore-and-aft sails). After transcribing a copy of her Rigging Warrant into an Excel Spreadsheet, I used some background formulas and pivot tables to calculate the various sizes of thread I would need and was very surprised with the result. This may not surprise the more experienced modellers, but needing over 71 metres of running rigging scale rope was somewhat enlightening for me (and that doesn't include some of the extraneous stuff like lacings, some rigging tackles, gun tackles, boat rigging (5 x boats) etc. Please note that I am using silver grey thread to simulate the wirerope rigging - using wire would simply destroy the rigging fittings at this scale. I am posting an example of one of the worksheets (that for the Bowsprit and combined Jib Boom) the spreadsheet. The scary bit - how do I make 0.1mm rope I think I will just have to find some suitable sized thread, or simply round these out a bit and use say only 3 or 4 sizes but stick to the principle of lighter ropes to the upper rigging etc. cheers Pat
  15. BANYAN
    Keith, can you get heat shrink of this small a diameter (and right colour)? Might make life a little easier for simulating the wire coverings. I love that photo of your helper (dockyard assistant) - looks like she is well on her way to lofting plans Hopefully I can encourage both my granddaughters to help cheers Pat
  16. BANYAN
    Thanks everyone for the comments and encouragement; and welcome aboard French Mr Bean - appreciate your kind comment. Good ideas Eberhard and Druxey, I will experiment with those techniques but I must admit I have never had much luck with concentricity when boring out cheers Pat
  17. BANYAN
    Just a small update, I have been fiddling around trying to determine the best way to make some of the swing boom fittings, and I think I have settles on the way to go. I have found some thin wall brass tube which has the correct ID for the spider band. Using my mill with an indexing head and sensitive drill attachment, I can drill small holes 90 degrees apart using a carbon bit (good bight on the brass). I have made some small eyes with a 0.5mm twisted shank which fit these holes nicely so that I can solder them in place. I then nip and file away any of the eye shaft in the ID of the tube leaving a nice smooth finish that slides onto the boom for a firm fit. The finished band look very acceptable when cleaned up and blackened. For the inner end fitting I have used some PE I had made that when put into a former and domed using a burnisher, provides the base of the fitting. I was having some issues getting the small thin strip to sit properly for me to solder so had to find another solution. I found a bit of thick walled brass tube that had near the right ID to slide over the arms of the fitting but had to ream that out a tad. I then pushed this onto a bit of scrap dowel and put a brass nail in to the end to expand the wood so the tube was held tightly. I then put that into my lathe and cut, filed and polished the OD of the tube to form a very thin wall. Once parted in the small saw jig (micro 'V' mitre box) the inner form could be removed leaving me with a nice thin band. I think the photos show this process but also shows that care needs to be taken even with a jig - one cut got away from me as you can see - the parted tube/band has a very rough edge where my sawing technique was not up to par - luckily I had enough to make plenty of the bands. Now to solder them into place. For comparison, the thickness of the formed base of the gooseneck fitting is 0.2mm and the ruler ticks are 1mm apart. cheers Pat
  18. BANYAN
    Ditto above comments; just when you think it can't get better than.... well, you continue to provide such lovely detailed fittings. cheers Pat
  19. BANYAN
    Nice work Rob, some significant progress. cheers Pat
  20. BANYAN
    Getting there indeed; looks great Greg. You have mastered these now so what is your next building challenge? cheers Pat
  21. BANYAN
    You're making great progress mate; looks good. cheers Pat
  22. BANYAN
    I think you have nailed it Dave, some ships I believed had fixed stanchions, but others removeable - the manropes were only fitted as required and usually had a Walkers Knot in the top end that went through the upper ring. cheers Pat
  23. BANYAN
    Love the planning you put into these micro builds Glen; looks like you have a winner here. cheers Pat
  24. BANYAN
    The boats etc turned out nicely, a lot better than those metal things. More goodies to play with; must be your birthday cheers Pat
  25. BANYAN
    we must have crossed in the ether Rob - great minds think alike (well your's might be great at least). cheers Pat

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...