Roger Pellett Posted May 20, 2020 #601 Posted May 20, 2020 Can’t hit the Like button on that one, OC. Why is that some projects continually fight us? Maybe turn it into an airplane half model? Seriously, I hope that you find a solution that allows you to consider this model finished. Roger Canute, popeye the sailor and Egilman 3 Quote
Egilman Posted May 20, 2020 #602 Posted May 20, 2020 1 hour ago, Old Collingwood said: Yep, the other side is fine, I have just this moment gone down stairs (as its night here now) and put a coat of micro sol over the affected decal/s I will check them in a couple of hours to see if (by miracle) the micro sol has worked - not holding my breath though. The problem is that top coat of Tamiya Laquer is key as it will either stop me working on the decal, or if I decided to try to remove the decal using tape to pull it off - I think the laquer will stop it or at worst pull a larger area of paint and laquer with it. OC. I agree the top coat is key, it was fine until that was laid... TBH, I have NEVER ever seen anything like that, all the other stuff wrinkles, popcorn ceiling effect, bubbles, orange peel I have all seen and fixed, this one has me stumped... that looks like hippopotamus/elephant skin...... Well let me know how the second application of Decal set/sol works.... I have a suspicion that it will not work through the overcoat...... This is one bird that doesn't want to be finished or likes the attention, it seems like it's taking on a personality..... We have all had them, your not alone... popeye the sailor and Canute 2 Quote Current Build: F-86F-30 Sabre by Egilman - Kinetic - 1/32nd scale In the Garage: East Bound & Down, Building a Smokey & the Bandit Kenworth Rig in 1/25th scale Completed: M8A1 HST 1930 Packard Boattail Speedster M1A1 75mm Pack Howitzer F-4J Phantom II Bell H-13's P-51B/C Temporary Suspension: USS Gwin DD-433 F-104C Starfighter "Blue Jay Four" 1/32nd Scale Terminated Build: F-104C Starfighter ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Quote: "Relish Today, Ketchup Tomorrow"
Old Collingwood Posted May 20, 2020 Author #603 Posted May 20, 2020 17 minutes ago, Roger Pellett said: Can’t hit the Like button on that one, OC. Why is that some projects continually fight us? Maybe turn it into an airplane half model? Seriously, I hope that you find a solution that allows you to consider this model finished. Roger Thank you Roger - yep frustrating. OC. Canute and popeye the sailor 2 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Old Collingwood Posted May 20, 2020 Author #604 Posted May 20, 2020 2 minutes ago, Egilman said: I agree the top coat is key, it was fine until that was laid... TBH, I have NEVER ever seen anything like that, all the other stuff wrinkles, popcorn ceiling effect, bubbles, orange peel I have all seen and fixed, this one has me stumped... that looks like hippopotamus/elephant skin...... Well let me know how the second application of Decal set/sol works.... I have a suspicion that it will not work through the overcoat...... This is one bird that doesn't want to be finished or likes the attention, it seems like it's taking on a personality..... We have all had them, your not alone... My suspicion is that I applied the top coat a bit too heavy on that side or perhaps it hadn't shrunk down as well due to the ridge it had to sit over, especially the end of the ridge causing an akward lump in the middle, possibly a bit of trapped air - that mde it an esy target for the top coat to loosen and craze the way it did. OC. popeye the sailor and Canute 2 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Egilman Posted May 20, 2020 #605 Posted May 20, 2020 I don't think it was trapped air brother, that's what micro sol and a pin is for, and you would see it as soon as the decal is dry cause it wouldn't lay down, more like trapped water IMHO...... popeye the sailor and Canute 2 Quote Current Build: F-86F-30 Sabre by Egilman - Kinetic - 1/32nd scale In the Garage: East Bound & Down, Building a Smokey & the Bandit Kenworth Rig in 1/25th scale Completed: M8A1 HST 1930 Packard Boattail Speedster M1A1 75mm Pack Howitzer F-4J Phantom II Bell H-13's P-51B/C Temporary Suspension: USS Gwin DD-433 F-104C Starfighter "Blue Jay Four" 1/32nd Scale Terminated Build: F-104C Starfighter ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Quote: "Relish Today, Ketchup Tomorrow"
Old Collingwood Posted May 20, 2020 Author #606 Posted May 20, 2020 18 minutes ago, Egilman said: I don't think it was trapped air brother, that's what micro sol and a pin is for, and you would see it as soon as the decal is dry cause it wouldn't lay down, more like trapped water IMHO...... Just been down put another coat of micro sol over the decals, will try to put a few layers on leaving an hour or so between layers - just to see if it does anything. OC. Canute and popeye the sailor 2 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
CDW Posted May 20, 2020 #607 Posted May 20, 2020 Just now, Old Collingwood said: My suspicion is that I applied the top coat a bit too heavy on that side OC. This Some decals don't like lacquer over top. But since it didn't give the other decals a problem, I suspect it's a matter of too heavy a coat. This is one of the limitations/difficulties of rattle can paint, a lack of flow control. Most of the time, decals will behave well to a light coat of clear lacquer, but a heavy coat will cause issues. It likely puddled here, which caused it. popeye the sailor and Canute 2 Quote Completed Projects: USS Fletcher 1:144 Scharnhorst 1:350 USS Independence LCS-2 1:350 1:32 J7W1 Shinden Interceptor/Fighter Fairey Swordfish Mk. II 1:48 Harbor Tug Box Scale Albatros D.V 1:32 Ala-Kart 1:25 Ferrari 250 GT California Spyder 1:24 S-100 Schnellboot 1:72 Mercury Capsule and Atlas Booster BR-52 Steam Locomotive 1:35 Triumph 3 HW Motorcycle 1:9 Scale F-16XL-2 Experimental Fighter Bomber 1:48 Rafale 1:48 F-15E Strike Eagle 1:48 Petlyakov PE-2 Soviet Dive Bomber 1:48 TBM3 Avenger 1:32 1931 Cadillac 1:25 Scammell Pioneer SV2S Heavy Breakdown Tractor 1:35 M-50 Israeli Sherman 1:35 Military Wrecker 1:32 Delahaye 135 1:24 Toyota Sard Supra GT 1:24 Enzo Ferrari 1:24 1970 Baldwin Motion Camaro 1:25 1966 Ford Galaxie 500 Stock Car 1:25 American LaFrance Eagle Fire Pumper 1:25 1940 Ford Standard Coupe 1:25 VolksWagen Dragster/Dune Buggy/Street Rod 1:25 Kawasaki Ninja H2 Carbon 1:12 Porsche GT-1 Evo 1:24 Scharnhorst 1940 1:700 IJN Akitsushima Seaplane Tender 1:700 HMS Hood 1941 1:700 Prinz Eugen 1942 1:700
Old Collingwood Posted May 20, 2020 Author #608 Posted May 20, 2020 3 minutes ago, CDW said: This Some decals don't like lacquer over top. But since it didn't give the other decals a problem, I suspect it's a matter of too heavy a coat. This is one of the limitations/difficulties of rattle can paint, a lack of flow control. Most of the time, decals will behave well to a light coat of clear lacquer, but a heavy coat will cause issues. It likely puddled here, which caused it. I will try my best to see what the repair or part repair options are - wll see what micro sol does, then (as I assume a barrier is on the model now) I will try another flat coat over the top to see if that might help hide the wrinkles (failing that its a Good anti - wrinkle cream)😉 OC. Canute and popeye the sailor 2 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Javlin Posted May 20, 2020 #609 Posted May 20, 2020 I feel your pain OC after four attempts(paint) on that night fighter 110 it went in the box for later have to find some different decals or something. CDW, Old Collingwood, Canute and 1 other 4 Quote
mtaylor Posted May 20, 2020 #610 Posted May 20, 2020 Do like many model ship makers do. If the other side is good, then the bad decal side is the "wall side". Roger Pellett, Canute and popeye the sailor 3 Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
Old Collingwood Posted May 20, 2020 Author #611 Posted May 20, 2020 19 minutes ago, mtaylor said: Do like many model ship makers do. If the other side is good, then the bad decal side is the "wall side". Indeed Mark, thats what I will have to do as despite several attempts with Micro sol, the orange peel aint going know where, the top coat has sealed them in. OC. Canute, mtaylor and popeye the sailor 3 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Egilman Posted May 20, 2020 #612 Posted May 20, 2020 1 hour ago, CDW said: This Some decals don't like lacquer over top. But since it didn't give the other decals a problem, I suspect it's a matter of too heavy a coat. This is one of the limitations/difficulties of rattle can paint, a lack of flow control. Most of the time, decals will behave well to a light coat of clear lacquer, but a heavy coat will cause issues. It likely puddled here, which caused it. I would agree, the decal floated in the lacquer.... there was a suggested way to kinda fix it on an online belog, but I've never had to do such... Hide it by gradually building up the clearcoat until most of it disappears..... Never tried it but at this point the only resolution is to hide it, or remove it and do it over..... I know cost becomes a factor... And since it is already under the clear lacquer.... Canute, mtaylor, popeye the sailor and 1 other 4 Quote Current Build: F-86F-30 Sabre by Egilman - Kinetic - 1/32nd scale In the Garage: East Bound & Down, Building a Smokey & the Bandit Kenworth Rig in 1/25th scale Completed: M8A1 HST 1930 Packard Boattail Speedster M1A1 75mm Pack Howitzer F-4J Phantom II Bell H-13's P-51B/C Temporary Suspension: USS Gwin DD-433 F-104C Starfighter "Blue Jay Four" 1/32nd Scale Terminated Build: F-104C Starfighter ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Quote: "Relish Today, Ketchup Tomorrow"
Old Collingwood Posted May 20, 2020 Author #613 Posted May 20, 2020 8 minutes ago, Egilman said: I would agree, the decal floated in the lacquer.... there was a suggested way to kinda fix it on an online belog, but I've never had to do such... Hide it by gradually building up the clearcoat until most of it disappears..... Never tried it but at this point the only resolution is to hide it, or remove it and do it over..... I know cost becomes a factor... And since it is already under the clear lacquer.... So, apply a couple more coats of flat over the top? OC. popeye the sailor, Canute and mtaylor 3 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Egilman Posted May 20, 2020 #614 Posted May 20, 2020 57 minutes ago, Old Collingwood said: So, apply a couple more coats of flat over the top? OC. I was reading about this on another forum... it was a way someone dealt with a similar issue.. (his was excessive bubbling after a gloss coat) successive light wet coats to raise and smooth out the surface.... it's the only thing I've found after a lot of searching the net.... other than ripping it off again and redoing it...... it actually didn't come out too bad... lmagna, mtaylor, popeye the sailor and 1 other 4 Quote Current Build: F-86F-30 Sabre by Egilman - Kinetic - 1/32nd scale In the Garage: East Bound & Down, Building a Smokey & the Bandit Kenworth Rig in 1/25th scale Completed: M8A1 HST 1930 Packard Boattail Speedster M1A1 75mm Pack Howitzer F-4J Phantom II Bell H-13's P-51B/C Temporary Suspension: USS Gwin DD-433 F-104C Starfighter "Blue Jay Four" 1/32nd Scale Terminated Build: F-104C Starfighter ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Quote: "Relish Today, Ketchup Tomorrow"
Old Collingwood Posted May 20, 2020 Author #615 Posted May 20, 2020 2 minutes ago, Egilman said: I was reading about this on another forum... it was a way someone dealt with a similar issue.. (his was excessive bubbling after a gloss coat) successive light wet coats to raise and smooth out the surface.... it's the only thing I've found after a lot of searching the net.... other than ripping it off again and redoing it...... it actually didn't come out too bad... Thanks mate, Very much appreciate and am thankful to you for searching stuff for my build, its help like this that makes this site so Special. OC. mtaylor, popeye the sailor, Canute and 1 other 4 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
cog Posted May 20, 2020 #616 Posted May 20, 2020 9 hours ago, Old Collingwood said: My suspicion is that I applied the top coat a bit too heavy on that side or perhaps it hadn't shrunk down as well due to the ridge it had to sit over, especially the end of the ridge causing an akward lump in the middle, possibly a bit of trapped air - that mde it an esy target for the top coat to loosen and craze the way it did. OC. did you use decal fixative, or only the softner? popeye the sailor, mtaylor and Canute 3 Quote Carl "Desperate affairs require desperate measures." Lord Nelson Search and you might find a log ...
Old Collingwood Posted May 20, 2020 Author #617 Posted May 20, 2020 3 hours ago, cog said: did you use decal fixative, or only the softner? I used both mate - both micro set then micro sol. OC. popeye the sailor, Canute, mtaylor and 1 other 4 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Old Collingwood Posted May 20, 2020 Author #618 Posted May 20, 2020 Just a small update fellow followers following freely forever figuring forensic feactures, so I played with the damaged decals, I decided to weather them to give them a worn look, I did this by gently sanding with very fine watered wet and dry, I did this both sides to keep a uniform look. Pics later after I have done a few light top coats. OC. cog, BLACK VIKING, popeye the sailor and 8 others 11 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
cog Posted May 20, 2020 #619 Posted May 20, 2020 2 hours ago, Old Collingwood said: Just a small update fellow followers following freely forever figuring forensic feactures, so I played with the damaged decals, I decided to weather them to give them a worn look, I did this by gently sanding with very fine watered wet and dry, I did this both sides to keep a uniform look. Pics later after I have done a few light top coats. OC. good choice OC Egilman, mtaylor, Edwardkenway and 3 others 6 Quote Carl "Desperate affairs require desperate measures." Lord Nelson Search and you might find a log ...
Old Collingwood Posted May 20, 2020 Author #620 Posted May 20, 2020 34 minutes ago, cog said: good choice OC Thanks mate. OC. Egilman, popeye the sailor, Edwardkenway and 2 others 5 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Old Collingwood Posted May 20, 2020 Author #621 Posted May 20, 2020 Here are a couple of pre top coat pics to show the affect after I have wet and dried over the decals gentley on both sides. OC. Javlin, marktiedens, Jack12477 and 12 others 15 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Egilman Posted May 20, 2020 #622 Posted May 20, 2020 3 hours ago, Old Collingwood said: Just a small update fellow followers following freely forever figuring forensic feactures, so I played with the damaged decals, I decided to weather them to give them a worn look, I did this by gently sanding with very fine watered wet and dry, I did this both sides to keep a uniform look. Pics later after I have done a few light top coats. OC. I think that was your best option my friend... The world hands you lemons, make lemonade.... I think that bird wants more than a pretty paint job, it wants to depict itself as the workhorse it actually was.... You have a special bird my friend.... cog, popeye the sailor, mtaylor and 3 others 6 Quote Current Build: F-86F-30 Sabre by Egilman - Kinetic - 1/32nd scale In the Garage: East Bound & Down, Building a Smokey & the Bandit Kenworth Rig in 1/25th scale Completed: M8A1 HST 1930 Packard Boattail Speedster M1A1 75mm Pack Howitzer F-4J Phantom II Bell H-13's P-51B/C Temporary Suspension: USS Gwin DD-433 F-104C Starfighter "Blue Jay Four" 1/32nd Scale Terminated Build: F-104C Starfighter ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Quote: "Relish Today, Ketchup Tomorrow"
Canute Posted May 20, 2020 #623 Posted May 20, 2020 Very nice recovery, OC! A flat coat and some weathering and no-ones the wiser. Edwardkenway, Egilman, mtaylor and 3 others 6 Quote Ken Started: MS Bounty Longboat, On Hold: Heinkel USS Choctaw paper Down the road: Shipyard HMC Alert 1/96 paper, Mamoli Constitution Cross, MS USN Picket Boat #1 Scratchbuild: Echo Cross Section Member Nautical Research Guild
Old Collingwood Posted May 20, 2020 Author #624 Posted May 20, 2020 5 minutes ago, Egilman said: I think that was your best option my friend... The world hands you lemons, make lemonade.... I think that bird wants more than a pretty paint job, it wants to depict itself as the workhorse it actually was.... You have a special bird my friend.... Thank you for those kind words. OC. Egilman, Edwardkenway, mtaylor and 2 others 5 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Old Collingwood Posted May 20, 2020 Author #625 Posted May 20, 2020 5 minutes ago, Canute said: Very nice recovery, OC! A flat coat and some weathering and no-ones the wiser. Thank you kindly Ken. OC. lmagna, popeye the sailor, mtaylor and 3 others 6 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
VTHokiEE Posted May 20, 2020 #626 Posted May 20, 2020 I like what you’ve done, such strong perseverance. I enjoy watching everyone work through these issues because I don’t have anywhere near the experience to think of these solutions. A great learning experience for me! Canute, Egilman, mtaylor and 4 others 7 Quote Current Build: HM Sloop Echo 1781 (First Scratch Build) Previous Builds: HM Cutter Alert, Sharpie Schooner, Chesapeake Bay Flattie, Half-Hull (NRG)
Old Collingwood Posted May 20, 2020 Author #627 Posted May 20, 2020 1 minute ago, VTHokiEE said: I like what you’ve done, such strong perseverance. I enjoy watching everyone work through these issues because I don’t have anywhere near the experience to think of these solutions. A great learning experience for me! Just me digging my teeth in and refusing to let it beat me, but thank you kindly for saying that. OC. lmagna, Egilman, Landlubber Mike and 5 others 8 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Old Collingwood Posted May 21, 2020 Author #628 Posted May 21, 2020 So after doing some internet bashing on the subject (not fly flishing🙃) later I will do a bit of shading using my pencil along some of the detail lines, then I will go over picking up the high spots with either a dull alum or white dry brush, as around the region where the dameged decals, there is a fuselage locker and the strenthening rib, the same needs to be done to the other stab where had to give it a re - paint. OC. Edwardkenway, lmagna, popeye the sailor and 3 others 6 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
mtaylor Posted May 21, 2020 #629 Posted May 21, 2020 Sounds like a good plan, OC. The recovery so far is looking great. Nothing like a few worn spots and some scars on a war bird. Egilman, Canute, lmagna and 2 others 5 Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
Old Collingwood Posted May 21, 2020 Author #630 Posted May 21, 2020 15 minutes ago, mtaylor said: Sounds like a good plan, OC. The recovery so far is looking great. Nothing like a few worn spots and some scars on a war bird. Thanks mate, just my logic - cover up the blemishes with blemishes - just intentional ones. OC. popeye the sailor, Egilman, Landlubber Mike and 3 others 6 Quote Current builds 28mm Battle of Waterloo attack on La Haye Saint Diorama. 1/700 HMS Hood Flyhawk with PE, Resin and Wood Decking. Completed works. Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic. HMS Warspite Academy 1/350 plastic kit and wem parts. HMS Trafalgar Airfix 1/350 submarine plastic. Black Pearl 1/72 Revell with pirate crew. Revell 1/48 Mosquito B IV Eduard 1/48 Spitfire IX ICM 1/48 Seafire Mk.III Special Conversion 1/48 Kinetic Sea Harrier FRS1
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.