Jump to content

Majellan by Omega1234 - Luxury 37 metre Motor Yacht - 1/200 Miniature 7 inches approx - Finished


Recommended Posts

Hi folks

 

As I'm fast approaching the completion of my current model, "Symphony", now's a good time to reveal my next project - a miniature model of a 37 metre luxury motor yacht, which I will name "Majellan". The plans will be loosely based on an existing ship, whose plans I found using using Google.

 

The model will have a fully detailed interior (well, as much as I can replicate at this tiny size, anyway)! Majellan's interior layout consists of the following decks:

 

-Lower Deck;

-Main Deck;

-Upper Deck; and

-Sun Deck.

 

The profile of the ship is provided below:

 

post-7645-0-66656600-1442148948_thumb.jpg

 

I hope to commence construction as soon as I can figure out how to build the darn thing!! Talk about a challenge.

 

If you're able to, I'd love it if you could please join me on Magellan's journey.

 

Cheers

 

Patrick

Edited by Omega1234
Link to comment
Share on other sites

Hi Nick, Nils, Bob, Dave and Mark

 

Thanks for joining me on Majellan's journey! I've cleaned all the seats to make sure you're all comfortable and feel welcomed; so please enjoy the journey.

 

Spread the word, too, as the more the better!

 

Thanks and all the best

 

Patrick

Link to comment
Share on other sites

Just saw you started a new log! Definitely on board, again. The concept for this 'small' (in mega yacht standards!) motor yacht reminds me of a design I did with a team of classmates my junior year of a ~150 ft (45m) motor yacht. We only did very preliminary/concept design, but enough to do some basic arrangements and naval architecture work (weight/stability/powering, etc). I'll have to see if I can dig something up on it from my files. I have hard copies of the drawings, but I think the original cad files are lost to the abyss....

Link to comment
Share on other sites

Hi everyone

 

Today I actually started on Magellan's hull.  As mentioned before, I intend to fully fitout Magellan's interior accommodation; all four decks of it.  How I intend to do this is by allowing each deck to be lifted off so that the interior can be viewed.  Talk about a challenge!!!  Oh well, if you don't try, nothing would be achieved.  

 

So, without further ado, the photos below show the start of the hull.  It may not look like much, but, hopefully it'll turn into one hell of a beauty!  A very long way to go, of course...

 

Wish me luck!

 

Cheers

 

Patrick 

post-7645-0-16691500-1443531454_thumb.jpg

post-7645-0-56996800-1443531466_thumb.jpg

Link to comment
Share on other sites

Congratulations on the start of the build, Patrick!

 

Maybe you want to populate the yacht crew and passengers? ))

 

http://ru.aliexpress.com/store/product/100pc-1-200-scale-white-figure-for-Landscape-Train-Model-Scale-architectural-scenery/816579_807820443.html

 

Best Regards!

Igor.

Link to comment
Share on other sites

Hi everyone

As I don't have any actual hull plans for Majellan's hull I'm building, I'm relying mainly on photos of other similar sized modern luxury yachts on the Internet.  Many of these modern motor yachts have very unusual underbodies. In fact, they're far from the graceful and streamlined beauties that you'd expect.  Instead, they're quite angular and, dare I say it, ugly underneath (well, to my mind, anyway)!

As a means of overcoming the lack of detailed plans, I decided to do a clay mock-up of what I think the hull could look like, using the examples of Internet photos I've seen.  Once I'm happy with what I've come up with, I'll then use the mock-up as a guide to carve the wooden hull.

The clay mock-up can be seen in the photos below.  There's still a long way to go before I'm happy with its shape, but it's a start.

Cheers

Patrick 

 

 

 

 

post-7645-0-62804400-1443620088_thumb.jpg

post-7645-0-82113800-1443620094_thumb.jpg

post-7645-0-38025100-1443620102_thumb.jpg

Link to comment
Share on other sites

Hi Patrick,

I'm looking forward to watching this build as well. Especially for this type of craft I would expect an inaugural cruise with lots and lots of babes in micro-micro bikinis!

Best,

John

 

Yeah! Agree with ya on that one. Now, where's me bikini....

Link to comment
Share on other sites

Looking good Patrick!

 

Only one Nav Arch suggestion for the hull. I would soften the chine (the 'corner') in the hull forward of amidship, so that by the time you get to where the bulb starts, the bulb fairs smoothly into the rest of the hull with little to no discernible chine. The entry will be finer, meaning the bulb will actually be efficient - as it is now, the bulb would generate a bow wave that would smack right into the abrupt shape change leading to the chine, and so it seems to me that it wouldn't do anything, hence the idea that the shape should be finer forward that what you have shown. (The intent of a bulb is to generate a bow wave that interferes with the bow wave generated by the stem proper, such that the two waves cancel out and less energy is transferred into the water.)

 

The other item that leads me to think the underwater hull forward is too severe is that the bow thruster is a bit aft of the bulb; with the hull as you have it shaped, the tunnel would be very wide, and the opening would be at a very strange angle, such that there would be a very elliptical opening. But if you make the hull a little finer, that should pull the side a little closer to vertical and reduce the width of the tunnel and also improve the opening in the side to be more circular.

 

But other than that one suggestion, I think you have the hull spot-on to what I've seen of hull models used for tank testing.

 

Keep up the good work!

Ben

Edited by BenF89
Link to comment
Share on other sites

Looking good Patrick!

 

Only one Nav Arch suggestion for the hull. I would soften the chine (the 'corner') in the hull forward of amidship, so that by the time you get to where the bulb starts, the bulb fairs smoothly into the rest of the hull with little to no discernible chine. The entry will be finer, meaning the bulb will actually be efficient - as it is now, the bulb would generate a bow wave that would smack right into the abrupt shape change leading to the chine, and so it seems to me that it wouldn't do anything, hence the idea that the shape should be finer forward that what you have shown. (The intent of a bulb is to generate a bow wave that interferes with the bow wave generated by the stem proper, such that the two waves cancel out and less energy is transferred into the water.)

 

The other item that leads me to think the underwater hull forward is too severe is that the bow thruster is a bit aft of the bulb; with the hull as you have it shaped, the tunnel would be very wide, and the opening would be at a very strange angle, such that there would be a very elliptical opening. But if you make the hull a little finer, that should pull the side a little closer to vertical and reduce the width of the tunnel and also improve the opening in the side to be more circular.

 

But other than that one suggestion, I think you have the hull spot-on to what I've seen of hull models used for tank testing.

 

Keep up the good work!

Ben

Hi Ben

 

Woohoo!!! Thanks for your feedback and advice. I was going to ask for your professional advice, but didn't want to bug you unnecessarily, but now that you've pitched in, I'm really grateful.

 

I'll trim the bow further to make the entry finer and thereby creating a smother transition to the bulb as you've suggested. Once done, Hopefully you can comment again to see if it's ok.

 

Cheers

 

Patrick

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...