Jack H Posted March 18, 2017 #1 Posted March 18, 2017 Hello to all! For my poor English ,the following was translated by software and maybe have some grammar or other mistakes . The plans of L'ARTÉSIEN were purchased from France in last year,the ship is so beautiful and i want to make it(into a ship model) by cnc. First I scan the drawings,then make it into 3d model or 2d Vector graph,Then NC engraving,Including 2D and 3d kits for example frames/figurehead... My project starts from the stem and the main material is pear and jujube... This process is almost all CNC machining, manual only assembly and polishing... some photos of Actually produced... mill on double sides The two faces are basically the same Double sides milling of bow special parts... The following is "no bridges" The previous production was "have bridges" As shown below... pre-assemble... The figurehead ... 3d model Although not very similar, I have tried my best... NC machining programming and simulation Preparation materials It will take some time to process the finished product Archi, archjofo, shipmodel and 27 others 30 Quote
WackoWolf Posted March 18, 2017 #2 Posted March 18, 2017 Beautiful work. Please keep the post and pictures coming. I will be following this to the end. Thank you for sharing this excellent work with us. Canute, Archi and mtaylor 3 Quote Wacko Joe Go MSW :)
druxey Posted March 18, 2017 #3 Posted March 18, 2017 A very interesting modern approach! mtaylor, Mirabell61, Archi and 1 other 4 Quote Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series http://trafalgar.tv
Kishmul Posted March 18, 2017 #4 Posted March 18, 2017 Lovely work, I'll watch this with interest. What software is being used for the figurehead? Thanks Ken Canute, mtaylor and Archi 3 Quote
Jack H Posted March 18, 2017 Author #5 Posted March 18, 2017 27 minutes ago, Kishmul said: Lovely work, I'll watch this with interest. What software is being used for the figurehead? Thanks Ken zbrush - Digital engraving software mtaylor, Kishmul and Canute 3 Quote
Kishmul Posted March 18, 2017 #6 Posted March 18, 2017 Thank you, I'll take a look at that! Ken Canute and mtaylor 2 Quote
Jack H Posted March 30, 2017 Author #7 Posted March 30, 2017 Because of a small mistake, the first attempt ended in failure, but there were also some gains. The second production has begun... dj.bobo, Captain Poison, Jeronimo and 15 others 18 Quote
herask Posted March 30, 2017 #8 Posted March 30, 2017 looking good. great modeling... ;-) Denis mtaylor 1 Quote cheers! Denis In Progress: HMS Pandora 3D modeling (temporarily on hold) Finished Builds: Swan Class HMS Pegasus for Admiralty Models 3D Build German Type VIIC U-Boat 3D model My other 3D work: Artstation
kees de mol Posted March 30, 2017 #9 Posted March 30, 2017 interesting methode. I will follow this build. mtaylor 1 Quote Current build: Dutch beamtrawler KW88, Pelikaan 1/75 Completed build: Dutch sidetrawler KW49, Antje 1/75 Completed build: Scottisch 10m trawler 1/25 Want to see some real Kitsch... With a capital K?!! Visit my 'museum' here at MSW My blog:
Jack H Posted March 30, 2017 Author #10 Posted March 30, 2017 Thanks attention For the first time, the face of the figurehead is too small .This error is caused by the failure of the Z axis when the milling cutter is broken. The difficulty of processing in the arms Archi, popash42, albert and 8 others 11 Quote
Jack H Posted March 31, 2017 Author #11 Posted March 31, 2017 shipmodel, Captain Poison, marsalv and 4 others 7 Quote
Jack H Posted March 31, 2017 Author #12 Posted March 31, 2017 Tim Curtis, mtaylor, Jeronimo and 6 others 9 Quote
Sailor1234567890 Posted March 31, 2017 #13 Posted March 31, 2017 What program did you use to draw the frames and bow in post #1? WackoWolf and mtaylor 2 Quote
Jack H Posted April 1, 2017 Author #14 Posted April 1, 2017 12 hours ago, Sailor1234567890 said: What program did you use to draw the frames and bow in post #1? rhino- industrial design software mtaylor and WackoWolf 2 Quote
Jack H Posted April 12, 2017 Author #15 Posted April 12, 2017 The fourth production AnobiumPunctatum, Archi, VTHokiEE and 17 others 19 1 Quote
shipmodel Posted April 12, 2017 #16 Posted April 12, 2017 By George, you've done it. Bravo! Dan mtaylor 1 Quote Current build -Khufu solar barge, c. 2,560 BCE, a cross-section model at 1:10 scale Prior scratch builds - Royal yacht Henrietta, USS Monitor, USS Maine, HMS Pelican, SS America, SS Rex, SS Uruguay, Viking knarr, Gokstad ship, Thames River Skiff , USS Oneida, Swan 42 racing yacht, Queen Anne's Revenge (1710), SS Andrea Doria (1952), SS Michelangelo (1962) , Queen Anne's Revenge (2nd model) USS/SS Leviathan (1914), James B Colgate (1892), POW bone model (circa 1800) restoration, SS Mayaguez (c.1975) Prior kit builds - AL Dallas, Mamoli Bounty. Bluejacket America, North River Diligence, Airfix Sovereign of the Seas "Take big bites. Moderation is for monks." Robert A. Heinlein
mtaylor Posted April 12, 2017 #17 Posted April 12, 2017 Fascinating to say the least. How long did it that the CNC to make the figurehead? WackoWolf, CaptainSteve, PeteB and 1 other 4 Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
Jack H Posted April 12, 2017 Author #18 Posted April 12, 2017 Thanks Dan and Mark for your attention. "Fascinating to say the least. How long did it that the CNC to make the figurehead?" Some areas that not carved by maching need secondary processing, it took me total about 18-20 hours to complete a primary processing- 0.8mm millcut/0.05mm stepover. druxey, WackoWolf, PeteB and 4 others 7 Quote
Jeronimo Posted April 23, 2017 #19 Posted April 23, 2017 Hallo, Regards Karl WackoWolf and mtaylor 2 Quote
Jack H Posted April 24, 2017 Author #20 Posted April 24, 2017 Thanks Jeronimo,and thanks everybody. Maybe I will stop the buildlog for a while,I promised the request of a member to development of a private drawing of the frame and make its sculpture, including the figurehead. This is the last update of the production of the figurehead. After the figurehead is fixed, the support is finally removed. Remove the fixed softener... Finally, It's also need to be manually modified/polished and so on... PeteB, Archi, marktiedens and 11 others 14 Quote
Tigersteve Posted May 4, 2017 #21 Posted May 4, 2017 Nice Steve mtaylor 1 Quote Current: Mayflower- Model Shipways Completed: Lowell Grand Banks Dory- Model Shipways English Pinnace- Model Shipways 18th Century Longboat- Model Shipways
Jack H Posted May 24, 2017 Author #22 Posted May 24, 2017 Although some busy, I still took the time to make the fifth figurehead, a little bit of regret is that some of the flaws of wood Cn processing out of the sculpture is quite accurate, basically the same as the design,because it was not polished yet, so looks more rough. KARAVOKIRIS, PeteB, druxey and 17 others 20 Quote
Hubac's Historian Posted July 23, 2017 #23 Posted July 23, 2017 Hi! I am completely fascinated by what you are doing here, and will be following along with great interest. In my opinion, the face of your figurehead - even in its rough, un-pollished state - is an improvement over the original. Jack H, mtaylor and PeteB 3 Quote We are all works in progress, all of the time.
Jack H Posted December 15, 2017 Author #24 Posted December 15, 2017 After an another project, I will write a new processing program and re - engraving the figure-head with V type milling cutter.I also modified two errors and the face （head),more finer engraving results can be obtained by using the V type milling cutter. Karrex, Mirabell61, rybakov and 12 others 15 Quote
Gaetan Bordeleau Posted December 15, 2017 #25 Posted December 15, 2017 Impressive work hjx! Jack H, mtaylor, Jeronimo and 1 other 4 Quote
Mirabell61 Posted December 16, 2017 #26 Posted December 16, 2017 Awesome figurehead HJX, you must have a lot of experience with CNC milling and the right milling cutters thereto.... Nils mtaylor, Jack H and PeteB 3 Quote Current builds -Lightship Elbe 1 Completed - Steamship Ergenstrasse ex Laker Corsicana 1918- scale 1:87 scratchbuild - "Zeesboot" heritage wooden fishing small craft around 1870, POB clinker scratch build scale 1:24 - Pilot Schooner # 5 ELBE ex Wanderbird, scale 1:50 scratchbuild - Mississippi Sterwheelsteamer built as christmapresent for grandson modified kit build - Chebec "Eagle of Algier" 1753--scale 1:48-POB-(scratchbuild) "SS Kaiser Wilhelm der Grosse" four stacker passenger liner of 1897, blue ribbond awarded, 1:144 (scratchbuild) "HMS Pegasus" , 16 gun sloop, Swan-Class 1776-1777 scale 1:64 from Amati plan -"Pamir" 4-mast barque, P-liner, 1:96 (scratchbuild) -"Gorch Fock 2" German Navy cadet training 3-mast barque, 1:95 (scratchbuild) "Heinrich Kayser" heritage Merchant Steamship, 1:96 (scratchbuild) original was my grandfathers ship -"Bohuslän" , heritage ,live Swedish museum passenger steamer (Billings kit), 1:50 "Lorbas", river tug, steam driven for RC, fictive design (scratchbuild), scale appr. 1:32 under restoration / restoration finished "Hjejlen" steam paddlewheeler, 1861, Billings Boats rare old kit, scale 1:50
mtaylor Posted December 16, 2017 #27 Posted December 16, 2017 Beautiful work HJX. Maybe I'm not seeing it but those carvings look perfect. Jack H 1 Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
Erebus and Terror Posted December 16, 2017 #28 Posted December 16, 2017 Very interesting build! Thanks for sharing! mtaylor and Jack H 2 Quote Building Terror Blog
Jack H Posted December 25, 2017 Author #29 Posted December 25, 2017 (edited) Thanks Erebus and Terror Nils Mark Gaetan Bordeleau and Hubac'sHistorian! I finished second steps, because my machine is 4 axis, so many parts need to be engraved again. In general, Maybe i can get better sculpture by using new model new processing program and the V type milling cutter. If the eyeball is to be engraved, 0.1mm V type milling cutter is needed, but I use 0.3mm milling cut now. The rssult of the left arm after additional carving. Edited December 25, 2017 by hjx JOUFF, marsalv, Archi and 12 others 15 Quote
Hubac's Historian Posted December 25, 2017 #30 Posted December 25, 2017 (edited) HJX, the milling results are really pretty incredible! Even with just a small amount of handwork, you could finish this carving on a level that most would really labor to achieve by sculpting alone. This is really a fascinating process that you use to make models. I’m glad to see you are still plugging away at it, and I look forward to your progress. Happy Holidays to you and all on MSW! Edited December 25, 2017 by Hubac'sHistorian mtaylor, Jeronimo and Jack H 3 Quote We are all works in progress, all of the time.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.