gjdale

Lovely joinery Bob.

I'll add my vote for the Sherline. A quality machine that is reasonably priced and with a huge range of accessories. And remember, "quality is remembered long after price is forgotten". A quality tool is a joy to use and I find great enjoyment every time I use my Sherline.

I see no starved cows here Slog - only well nourished ones! Great job. Looking forward to more progress.

Nice to see you back with an update Joachim. She's looking fabulous!

Congratulations on completing a fine build Gary. You can be justifiably proud of this - a really significant achievement!

I can’t believe a month has gone by without posting progress. It seems to have been a month filled with small steps that suddenly arrived at a major milestone. The next job was to make the Rear Fenders. Again, the kit provides sticky aluminium strips for this, but I decided to replace these with polished stainless steel, complete with 00-90 screws. I first created a template for the screw holes in CAD and printed this onto sticky label paper. The 0.5mm thick stainless steel was ripped to width by temporarily sticking it with double sided tape to a carrier of scrap timber and passing it through by Byrnes saw. The template was then attached to the stainless steel blank and the 1/16” screw holes drilled on the drill press. The ends of the piece were marked by scribing through the template and then cutting by hand with small hack saw. The piece was then polished up prior to removal from the carrier and installation on the hull. Double sided “attachment tape” from MACK products was used to install the fenders. Holes were then drilled into the hull, using the pre-drilled fender holes as locators, and the 00-90 screws epoxied in place using 15 minute cure epoxy. A similar technique for the screws was used on the cutwater, the difference being that the main cutwater piece itself was also epoxied in place. Here is a close up of the cutwater – although the photo shows that it has suffered a little from handling and needs another polish-up. I then installed the rub rails. These run the full length of the hull at the sheer, with a second, partial one just above the water line that runs from the rear fenders forwards for about 8 inches. Instead of using the kit provided material for these, I used another MACK products item, which was very easy and quick to apply. It comes with a self-adhesive backing, although mine had suffered from heat and/or packing and postage, and was basically unusable. I stripped the remains of the adhesive off and replaced it with a narrow band of attachment tape, which achieve the same outcome. It was then time to prepare for the maiden voyage in the domestic testing facility. In preparation for testing, lithium grease was packed into the shaft stuffing tube and the rudder tube, and the running gear re-attached. This photo shows the brass prop and rudder in place (both also in need of a polish). You can also see here the brass strut that I made to replace the solid plastic skeg to support the stuffing box/shaft. I also decided that it was time to start installing the interior gear prior to installing the engine hatches, before space got too limited. This started with running the wiring for the bow and stern lights, through the conduit that I had previously installed. Here’s a couple of overall shots prior to tank-testing. You can see the ends of the wires for the lights in these shots, as well as the rub rails. And finally, we got to the tank test – she floats! And she doesn’t leak! Next up will be to finish installing all of the electrics prior to fixing the hatches in place and commencing on the final trim pieces. We’re getting close!

Put me down for a copy too Greg! Lovely work so far.

Great job Daria. Make sure Dad doesn't take over too much - it's too much fun!

What John said!

Sorry to hear of your health scare Mark, but glad to hear you're on the road to recovery and back in the shipyard.

Okay, I'm here now Danny. You may proceed!

Outstanding Danny. Both model and presentation are first rate - as we've come to expect from you!

Definitely NOT hitting the "like" button on that one Bob! Hope your repairs go smoothly.

Congratulations Danny, another fine model. Looking forward to your next one.

Tedious it may be, Bob, but well worth the effort! Looking very nice indeed.

Think I'll join th crew following this one John, as I have this kit in my stash for "one day". You're certainly off to a great start.

Lovely work Gary. Your attention to precision is really paying off.

Nice to see you back at the workbench Daria. Good effort on the first planking - can't wait to see you complete the second planking.

Jay - you're killing me! Stop feeding my addiction. No don't stop. Yes, please stop, No, don't stop...........................

Looking lovely Bob. Your low-tech clamping method obviously works well.

Thanks so much Marc

Thanks very much Popeye and Sam.

Thanks so much Gerhard, Bob and Rusty, and all of the "likes".

Congratulations on completing a lovely build Aydin.

Congratulations on another masterpiece Chuck.