Jump to content

Recommended Posts

Posted

Hi Druxey,

 

Darker white will be last. With this stove,  I want brick and mortar but there are  many difficulties. First the colors, could be right by painting as I tried earlier with the bakery oven for the bricks but no mortar. With this stove lines are straight and it should be easier to introduce mortar. Again it would be too soon to paint the mortar because at the end of assembly, sanding will be needed and it would sand a lot of paint. So to retain the color I choose a full color in the wood. The mortar is surely too white, I realize it is also too thick when I look at the pictures, even if I taught the thickness proportion was fine when I cut it. I did it by eye but I should have done calculate some proportions.  The most difficult width to obtain is the top panel with the curve. Ideally I should have done the panel and then do sides and bottom, but I did the contrary and the width does not fit exactly so I had 2 layers of mortar at 2 places. Assembly is not so easy also. horizontal mortar lines are easy but not the vertical lines are difficult because it is difficult to cut to the good lenght and to install. In fact this is exactly for this kind of reasons that I prefer to build at a bigger scale, to have a bigger ease to hold parts and enjoy the construction instead of worrying how to hold the small parts.

 

I do not know what would be the best method yet but it is surely fun to try few ones.

Posted

Gaetan,

Do I understand correctly that when making the grates, you stacked multiple blades on a Byrnes Saw?

 

Richard

Richard
Member: The Nautical Research Guild
                Atlanta Model Shipwrights

Current build: Syren

                       

Posted (edited)

Here are the ''targettes"".

 

    first 3 pictures with different lighting :

 

Off camera flash

Speedlight

Ambient light

 

No flash, no details

 

Without flash, it is difficult and sometimes impossible  to see small parts details.

 

For these pictures, scale is 1/24, which is big, so imagine  at 1/100 without flash!

post-184-0-08593500-1461425361_thumb.jpg

post-184-0-94874100-1461425361_thumb.jpg

post-184-0-89622100-1461425362_thumb.jpg

post-184-0-20021700-1461425364_thumb.jpg

post-184-0-15409400-1461429203_thumb.jpg

Edited by Gaetan Bordeleau
Posted

What surprised me, Geatan, is the difference between the images, not as much the colour - for that I expected, but for the red glow - however, the focus on the first seems much better than on the other two, which are with lighting oddly enough ...

Carl

"Desperate affairs require desperate measures." Lord Nelson
Search and you might find a log ...

 

Posted

Carl, 

 

-no attention or correction was given to the color, the red  could be  corrected  before and/or after the picture

-attention was given only to  sharpness  

-the difficulty is this image is to see the 2 black straps on a black plate

 

Is the focus in the first image? May be.

Would it have been possible to do as well with the 3 images? probably with more time, it was just a fast comparison 

 

The idea was just to demonstrate:

the importance of lighting which is neglected as much in model building as in photography

and the possibility to see more with a good lighting

Posted

Seeing your reference, Gaetan, have you tried melting the end of the brass rod to form the 'bouton'? I've found that by holding the rod or wire vertically (not with my fingers!) and holding the torch at about 45 degrees, the tip of the metal will melt and form a round ball. You could then flatten it if you want.

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Posted

Adding some  little details.

Here are some ideas about the 2 doors aft the second deck to go to the bathrooms.

Door knobs are always installed to the right because most of the peoples are right handed.

The port one open from front to aft.

The starboard one opens from aft to front.

 

Knowing that  deck is  higher aft than fore; 

It is easy to open the starboard one and there would be some space under when open.

The port one was a bit more complicated because the door opening from fore to aft would want to enter in the deck which is impossible.

 

The easy way to solve this is to cut the door from the bottom so that the bottom  does not get stopped by the deck.

In addition reinforcement wood angles are installed in each corner.  The height of these pieces  passes just in front of these doors.

 

May be all of this is false. If We compare with a picture already shown in this forum, there are 2 doors.

On one the door knob is to the right and on the other the door knob is to the left.

But at least we agree on 1 thing the bottom of the door had to be lift  so that the door could be opened.

post-184-0-96821600-1461962084_thumb.jpg

post-184-0-18263500-1461962086_thumb.jpg

post-184-0-20207100-1461962087_thumb.jpg

post-184-0-25419100-1461962088_thumb.jpg

post-184-0-22105700-1461962089_thumb.jpg

post-184-0-36499700-1461962090_thumb.jpg

post-184-0-85761500-1461963273_thumb.jpg

  • 2 weeks later...
  • 2 weeks later...
Posted

thanks for the rope coil tip

 

Richard

Richard
Member: The Nautical Research Guild
                Atlanta Model Shipwrights

Current build: Syren

                       

Posted

Hi Gaetan,

 

I'm interested in the third hand I saw in one of the above pictures, because I'm not very keen in the usual alligator clamps.

Could you tell me where you acquired them and at what price ?

I live in Europe (Belgium).

 

TIA,

Marc

Keep on modelling,

Marc

Posted

No words, Gaetan.  The pictures have stunned my brain cells.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Posted

Hi Gaetan,

 

I've been following your build from the earliest posts. The combination of your build and photographs can only be described as model ship building porn!

 

Best,

John

Member:

Connecticut Marine Model Society

Nautical Research Guild

Model Ship World

"So we beat on, boats against the current, bourne back ceaselessly into the past" F. Scott Fitzgerald - The Great Gatsby

"If at first you don’t succeed.......skydiving is probably not for you”

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...