Jump to content

SD-14 Cargo ship by Kevin - SD-14 Model Company - 1/70 - CARD - middle section


Recommended Posts

  SD141.JPG

 

Sometimes known as the replacement for the famous "Liberty" ship, the 14,000 ton SD14 general cargo ships are found under many different names and flags in most of the world's ports and all of the high seas. The designation "SD14" denotes "Shelter Deck 14,000 tons". The shelter deck is the second or tween deck in the cargo spaces and, when the ship is loaded down to her plimsoll line, she displaces 14,000 tons.

By the mid 1960s, there remained some 700 Liberty and other war-built cargo ships still trading. Even the youngest were 20 years old and the question of a replacement was exercising the minds of ship owners and builders around the world. the emergence of bulk carriers and container ships pointed to the end of the "shelter Deck" design which had been used with little alteration since the turn of the century. Many felt that this design was no obsolete and that the future lay with containerisation.

It was, therefore, something of a surprise when ship builders all over the world unveiled their plans for the "liberty Ship Replacement", almost all of which offered a two-deck vessel of 14,000/15,000 tons deadweight. Doubtless this choice was influenced by the requirements of potential customers. Most of the war-built vessels were, by this time, being operated by Greek ship owners of limited resources to whom these new designs, for a type of vessel with which they were fully experienced and priced at about £1 million with cheap credit facilities, were very attractive.

A total of 30 designs were put forward as the "Liberty Ship Replacement" in the early months of 1966. Of these, the most successful was the SD14, developed by the Sunderland shipbuilders, Austin and Pickersgill. The first SD14 keel was laid on 8th. June 1967. Unusually, this was not at Austin and Pickersgill's own yard, but nearby at that of another Sunderland shipbuilder, Bartram's, who were building the ship under licence. The first ship, named Mimis N. Papalios, was launched on 1st. December 1967. She was also very nearly the first SD14 to be completed. However, Austin and Pickersgill managed to make up the leeway in their own building programme to hand over the first completed SD14, the Nicola, on 14th. February 1968, the Mimis N. Papalios following the next day.

Between 1968 and 1988, a total of 211 SD14s were completed and it is interesting to note that, by 1990, only 10 had been scrapped for commercial reasons, a further three going to the breaker's yard after marine accidents. Of the dozen vessels reported as sunk, at least two fell victim to missile attack during the Iran/Iraq conflict.

Like the original Liberty ships, which many thought would be scrapped as soon as the war was over, the SD14 was not ascribed a very long life by some early critics. Nevertheless, these ships are still in demand in the charter market, with average daily rates of $5,200 for a one-year time contract, and in the second hand market with prices ranging from $2.5m for an early seventies ship to $5.75m. for a newer example.

One guide to the success of the SD14 is to look at the movement of the 211 ships through the second-hand market. Most of the ships now sailing are with only their second owner, a few remaining with their original purchaser. The oldest SD14 in service is the Wave Crest, the vessel which, as the Mimis N. Papalios, missed by one day the distinction of being the first completed ship of her type.

  SD142.JPG The Model

In 1978, while attached to Manchester Docks, George Robinson, a retired Merchant Navy captain, hit on the idea of providing the port fire brigade with an easy-to-build model of the SD14. In this way, the trainee firemen could easily and quickly become familiar with the layout of the ship.

So, originated a 2-foot long, 1:70 scale model kit of the Forward section of the SD14. This first attempt met with such success that kits if the Midships and After sections followed in 1979, the complete model measuring an imposing 7 feet in length. Professional and international recognition followed in 1982 when the model won the "Shipwrights Model Competition" at the Guildhall in London.

Quite apart from sheer size, the kit is remarkable, for it is, in fact, put together in much the same way as the original was in Sunderland. Space here permits no more than a brief glimpse of what awaits the builder of this miniature leviathan.

The instructions, which, for the complete kit, run to about 60 pages, first explain that the model will be built by the dry dock method rather than on the slipway - the difference is clarified.

You then proceed to lay the shell bottom plates of the Forward section to form the double bottom, between the outer surface of the hull and the inner surface of the holds. On the original, the space in between in used for water ballast, necessary to keep the propellor submerged when there is no cargo and to maintain an even keel. This last expression, in such common and, I suspect , often unwitting, usage, is precisely defined.

The building progresses aft as the cargo holds are each constructed with transverse watertight bulkheads, hold pillars and centre line plates. There are even properly runged ladders on which to descend to the bowels of the vessel. In the After section, as well as a cargo hold, there is the engine room together with the propellor shaft tunnel and, by lifting up the after deck house, access is provided to the steering gear flat and the rudder stock.

In the bridge superstructure, containing the crew's accommodation, every cabin is accounted for. The crew's mess room, galley and smoke room are each separately delineated as are the linen locker, baggage room and officers' smoke room to mention but a few. The model also incorporates the correct ventilation trunk ways, the significance of which for cargo handling is explained.

In the course of construction, the instructions are supplemented by sections which explain the actual fabrication of the original, so that, as you work through the model, you learn about the SD14, how it was assembled and how it works.The operation of such components as MacGregor hatch covers, the keelson and camber in the original are fully expounded and you can then reproduce these to scale. Step-by-step diagrams illustrate the sequence of construction.

It is perhaps worth remembering that ships are machines, the largest ever built by man. So it is fascinating to see how this great machine works and to reproduce it in miniature at the same time. The correct nautical terms are used and explained, showing how each part of the ship functions and how the whole design draws on centuries of experience to produce the modern ocean-going vessel. If, like me, you have wondered what exactly is a "Tween Deck" and what is its purpose, you need wonder no more. All is revealed after which you can actually build one.

The kit is printed on 184 A3 sheets of top quality manilla card, there being approximately 4,500 pieces, and the modeller can choose to paint the model with an authentic colour scheme or one of his own choice. The three sections can be fixed together or left dismantled and the aft superstructure can be removed to give a glimpse of the various deck levels inside the hull. naturally, all the cargo hatches open to show the holds.

. The model can be made either for display or, with suitable waterproofing (see "Cutting Remarks" no. 3), can be sailed, there being space for R/C gear.

Although the original SD14 models were all sold out about 10 years ago, Marcle Models, under licence from George Robinson, reissues the SD14 kit. The complete kit, weighing over 17 lbs, is supplied in 6 cartons, complete with a tool kit and costs £280 including worldwide surface mail. The three sections, Forward, Midships and After, are each available separately at £105 each.

Should you decide to have a go, this, the "Non plus ultra of card (and perhaps any other type of) modelling, should keep you busy for about a year.

 

SD143.JPG

 

Christopher Cooke and Thomas Pleiner, with acknowledgements to George Robinson, John Lingwood and Ships Monthly. Article first appeared in "Cutting Remarks" No. 4, September 1992.

 

Link to comment
Share on other sites

On a previous attempt to build this, we had a disaster, which resulted in the whols lot going to land fill, even though it was only fractionally completed, but I vowed to attempt again in the future

To be worked on alongside the Victory build space permitting (this is over 7 feet long, when built as a complete vessel and the Victory must take priority 

intentions are to build as 3 static displays with weathering, and led lighting

 

The sheets 180 of them are well printed and the instructions are very clear,, here are a few photos as she arrived today, having been ordered yesterday from Model Dockyard 

 

 

post-846-0-43947800-1472846651_thumb.jpg

post-846-0-19688300-1472846655_thumb.jpg

post-846-0-65468400-1472846658_thumb.jpg

post-846-0-76097500-1472846660_thumb.jpg

post-846-0-33882300-1472846663_thumb.jpg

post-846-0-81250900-1472846665_thumb.jpg

post-846-0-67683200-1472846668_thumb.jpg

post-846-0-53594800-1472846670_thumb.jpg

post-846-0-51441800-1472846672_thumb.jpg

post-846-0-97965900-1472846674_thumb.jpg

Link to comment
Share on other sites

I would have to admit, that looks like it would be an impressive builders model.  I also liked the history of this type of ship and was surprised how many are still in service.  

 

Current Builds:  Revell 1:96 Thermopylae Restoration

                           Revell 1:96 Constitution COMPLETED

                           Aeropiccola HMS Endeavor IN ORDINARY

Planned Builds: Scientific Sea Witch

                            Marine Models USF Essex

                            

 

Link to comment
Share on other sites

WOW!!! This should be an amazing build. I'm in!

Tim

 

Current build: Continental Navy Frigate ALFRED (build log)                      

Past builds:     Steam Tug SEGUIN (build log in the kits 1850-1900 section)       

                         Liberty Ship SS Stephen Hopkins (Gallery & Build Log)

                         USS Basilone (DD-824) (Gallery & Build Log)

                         USS Olympia (Gallery)

                         USS Kirk (FF-1087) (Gallery & Build Log)

 

 

                        

Link to comment
Share on other sites

I the shelter deck idea was a successful gimmick to minimize tonnage (a measure of internal volume used as the basis for calculating certain operating costs such as canal tolls, port charges, dry docking charges, etc.) without actually affecting the vessel's cargo carrying capacity.

 

Tonnage is calculated in accordance with internationally accepted rules and these rules exclude areas of the ship "open to the weather." The shelter deck was penetrated by one or more tonnage openings-small hatches that were not sufficiently watertight to meet the definition of a watertight closure for tonnage purposes but sufficiently robust to not affect freeboard calculations. For tonnage purposes the shelter deck was therefore considered to be open to the weather.

 

Roger Pellett

Link to comment
Share on other sites

Thought that the Triple Expansion Steam Engine powered Liberty Ship was replaced by the Steam Turbine powered Victory Ships with 3 Holds forward and 2 aft. There were quite a few Victory Ships steaming around the world in the 60's when I was in the Navy, one was ahead of us Transiting the Panama Canal in 66. :pirate41:

jud

Edited by jud
Link to comment
Share on other sites

Victory, Bismarck, and now this huge beast.  You don't go for the easy ones, do you Kevin?  ;)    I'm looking forward to seeing this.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

Count me in!

 

I've wanted to see one of these built for some time. Maybe I'll grab one as well, should the opportunity arise.

 

Andy

Andy

 

I know of only one place that this can be obtained, http://www.model-dockyard.com/acatalog/SD14.html, the price hasnt changed much in 5 years, but it is only carrdboard

Link to comment
Share on other sites

Kevin,

 

wish you good keellaying with this project.

Are you aiming to build one of the three sections or the whole ship. I noticed that its a card model, so you will be facing thousands of pieces to be orgenized logistic wise....., quite an ambitious task... ;)

 

Nils

Current builds

-Lightship Elbe 1

Completed

- Steamship Ergenstrasse ex Laker Corsicana 1918- scale 1:87 scratchbuild

"Zeesboot"  heritage wooden fishing small craft around 1870, POB  clinker scratch build scale 1:24

Pilot Schooner # 5 ELBE  ex Wanderbird, scale 1:50 scratchbuild

Mississippi Sterwheelsteamer built as christmapresent for grandson modified kit build

Chebec "Eagle of Algier" 1753--scale 1:48-POB-(scratchbuild) 

"SS Kaiser Wilhelm der Grosse" four stacker passenger liner of 1897, blue ribbond awarded, 1:144 (scratchbuild)
"HMS Pegasus" , 16 gun sloop, Swan-Class 1776-1777 scale 1:64 from Amati plan 

-"Pamir" 4-mast barque, P-liner, 1:96  (scratchbuild)

-"Gorch Fock 2" German Navy cadet training 3-mast barque, 1:95 (scratchbuild) 

"Heinrich Kayser" heritage Merchant Steamship, 1:96 (scratchbuild)  original was my grandfathers ship

-"Bohuslän" , heritage ,live Swedish museum passenger steamer (Billings kit), 1:50 

"Lorbas", river tug, steam driven for RC, fictive design (scratchbuild), scale appr. 1:32

under restoration / restoration finished 

"Hjejlen" steam paddlewheeler, 1861, Billings Boats rare old kit, scale 1:50

Link to comment
Share on other sites

Kevin,

 

wish you good keellaying with this project.

Are you aiming to build one of the three sections or the whole ship. I noticed that its a card model, so you will be facing thousands of pieces to be orgenized logistic wise....., quite an ambitious task... ;)

 

Nils

Good morning Nils

she will definitely not be going near water, and I dont have room for another build at 7' long (210cm), so she will be build as 3 completely separate builds, one possiblt as new, another in maint period, and another as a well used dirty hard working sea trader, would like to use some led lighting and find a supplier for some 1/70 deck fittings

Link to comment
Share on other sites

Thanks Kevin,

 

very interesting project and a good idea with displaing different stages of ussage. It could get a bit difficult to find suitable deck fittings in scale 1:70, but there I trust 1:72 would do as well, and provide some finds

 

for ladders  / Stairways I like to use this source  http://www.hobby-lobby-modellbau.com/onlineshop/index.php/cat/c468_Niederg-nge.html

 

Good luck and much fun with your build

 

Nils

Current builds

-Lightship Elbe 1

Completed

- Steamship Ergenstrasse ex Laker Corsicana 1918- scale 1:87 scratchbuild

"Zeesboot"  heritage wooden fishing small craft around 1870, POB  clinker scratch build scale 1:24

Pilot Schooner # 5 ELBE  ex Wanderbird, scale 1:50 scratchbuild

Mississippi Sterwheelsteamer built as christmapresent for grandson modified kit build

Chebec "Eagle of Algier" 1753--scale 1:48-POB-(scratchbuild) 

"SS Kaiser Wilhelm der Grosse" four stacker passenger liner of 1897, blue ribbond awarded, 1:144 (scratchbuild)
"HMS Pegasus" , 16 gun sloop, Swan-Class 1776-1777 scale 1:64 from Amati plan 

-"Pamir" 4-mast barque, P-liner, 1:96  (scratchbuild)

-"Gorch Fock 2" German Navy cadet training 3-mast barque, 1:95 (scratchbuild) 

"Heinrich Kayser" heritage Merchant Steamship, 1:96 (scratchbuild)  original was my grandfathers ship

-"Bohuslän" , heritage ,live Swedish museum passenger steamer (Billings kit), 1:50 

"Lorbas", river tug, steam driven for RC, fictive design (scratchbuild), scale appr. 1:32

under restoration / restoration finished 

"Hjejlen" steam paddlewheeler, 1861, Billings Boats rare old kit, scale 1:50

Link to comment
Share on other sites

Link to comment
Share on other sites

well I made the decision to progress the SD14 during the week, alongside my wife's projects and the Victory at the weekends, its a good compromise 

 

So here we go

Link to comment
Share on other sites

SD14 - Midships Section - Shell bottom plates

 

Total build time 2 hours

 

 

 

Started of by cutting out all the plates from the 1st four sheets, which is the bottom of the ship,  all the frames are numbered and knowing that port is even numbers it is quite easy to follow the instructions, however care is needed to ensure that all the lines do align

post-846-0-45527700-1472935116_thumb.jpg

 

laid out on the work bench, all these make up the midships section 29" long

post-846-0-50799200-1472935268_thumb.jpg

 

and the first plates are joined,there is quite an overlap, presently I am using Elmers PVA

 

post-846-0-72194800-1472935361_thumb.jpg

 

Link to comment
Share on other sites

congratz to you Kevin on the start of this mammoth build.   will you be able to join it together at some point,  to show it's size?    that would be so cool to see!

Edited by popeye the sailor

I yam wot I yam!

finished builds:
Billings Nordkap 476 / Billings Cux 87 / Billings Mary Ann / Billings AmericA - reissue
Billings Regina - bashed into the Susan A / Andrea Gail 1:20 - semi scratch w/ Billing instructions
M&M Fun Ship - semi scratch build / Gundalow - scratch build / Jeanne D'Arc - Heller
Phylly C & Denny-Zen - the Lobsie twins - bashed & semi scratch dual build

Billing T78 Norden

 

in dry dock:
Billing's Gothenborg 1:100 / Billing's Boulogne Etaples 1:20
Billing's Half Moon 1:40 - some scratch required
Revell U.S.S. United States 1:96 - plastic/ wood modified / Academy Titanic 1:400
Trawler Syborn - semi scratch / Holiday Harbor dual build - semi scratch

Link to comment
Share on other sites

congratz to you Kevin on the start of this mammoth build.   will you be able to join it together at some point,  to show it's size?    that would be so cool to see

The option is there to join the three together, but I am at present (early days) thinking about a life cycle of a sea trader, and have one section as new, one in mid life dockdown/refit and a very tired run down end of life section

Link to comment
Share on other sites

SD14 - Midships Section - Shell bottom plates


 


Total build time 6 hours


 


56 built pieces


 


took a good four hours to get all the plates in the right places, needing to set up longitudinally and transversely, the lines on the card are not perfect, they vary slightly in thickness and, well it even says in the instructions this is by no means an easy task


for info this part of the ship alone is 36.9 inches long


 


 


post-846-0-02118800-1473016178_thumb.jpg


this is the next set of cards which are the double bottom longitudinals, each one needs to be be cut out and then removes the slots (all good fun)


 


post-846-0-20980200-1473016181_thumb.jpg

Edited by Kevin
Link to comment
Share on other sites

OOOHHHHH! I wanted this ship 15 yrs ago and passed it up as too expensive and time consuming. Now you have brought it to light again and I covet it dearly. Please say something terrible about this build so I can once again put it out of my head. Bill longing in Idaho ;)

Bill, in Idaho

Completed Mamoli Halifax and Billings Viking ship in 2015

Next  Model Shipways Syren

Link to comment
Share on other sites

Link to comment
Share on other sites

Bill not going to say anything terrible about it, Just buy it, don't take any space up, until you start building it, LOL just go for it

Link to comment
Share on other sites

build time 12 hours

pieces fixed into position 112

 

Good evening everyone

 

all the longitudinals, are now in position  with the exception of some of the centre keelsoms, doesn't look much i know but the next plates should start to tie it all, in, all this will then be hidden when the deck plates go on

post-846-0-11962400-1473455431_thumb.jpg

post-846-0-43500900-1473455437_thumb.jpg

post-846-0-48249400-1473455624_thumb.jpg

Edited by Kevin
Link to comment
Share on other sites

Hey There Kevin.. Am looking forward to seeing this build develop, I've always liked the look of those SD14's since I first saw one in Tunisia  in the mid 80's.. Was actually looking to frame the Plans of one but couldn't find them anywhere,  I must take another looksie shortly  ^_^

 

I saw the bow section many years ago but never realised it was card.. WOW

 

All The Very best

 

Eamonn

Current Build   :  HM Schooner Ballahoo

In the Pipeline :  HM Cutter Sherbourne, HM Mortar Convulsion, Emma C Berry & C18th English Longboat.. Eventually That Is..🙄

Link to comment
Share on other sites

Good evening everyone

looks like again this is going to be one of those projects that does not seam to grow very fast even considering the time put in

I appreciate this is not a race, but I like to  post  my progress as some of you also watch my HMS Victory build

anyway the transverse frames continue to be cut out (two on each frame, a port and starbord,) slotted and moved into position, now up to frame 89  - which started at 50 and the last one on this section of the build is 130

this is a very easy build, but very repetitive, but at the same time it is quite enjoyable, the size of it alone make it a fascinating build

please note that apart from the longitudinal frames  non of the transverse frames have been glued, this at present is just slotted card being held in to position by the fwd to aft frames, the centre line will be sorted towards the end

 

post-846-0-75160300-1474225501_thumb.jpg

post-846-0-96597500-1474225503_thumb.jpg

post-846-0-73617300-1474225506_thumb.jpg

post-846-0-80831800-1474225508_thumb.jpg

post-846-0-88363100-1474225511_thumb.jpg

post-846-0-06391000-1474225514.jpg

Link to comment
Share on other sites

A ship manager I worked with liked to say it's a 3D business: Dirty, Difficult and Dangerous.

 

====================================

Currently building: Model Expo AMERICA, A/L KING OF THE MISSISSIPPI

 

Completed: Mamoli Victory cross-section, Revell LSM (Plastic, in memory of Dad), A/L SANSON tug, MS Longboat (awesome model Chuck!), Dumas 1949 Chris-Craft 19' Racing runabout, A/L SWIFT, MS ELSIE, Constructo ELIDIR (now LOUISE), Midwest Muscongus Bay Lobster Smack, Amati 1:80 Yacht ENDEAVOUR, Mamoli CONSTITUTION cross section, Revell VIIc U-boat (1:72 plastic), lotsa other plastic ships 

 

Next up: who knows - there are too many to choose from!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...