Jump to content

Duchess of Kingston c.1780 by James H - FINISHED - Vanguard Models - 1:64


Recommended Posts

Good morning!

 

As my Amati HMS Victory is currently on hiatus due to needing a good number of sheet replacements, I'll start work immediately on the future Vanguard Models release of the Royal Yacht, 'Duchess of Kingston'. As with my other VM stuff, this will be for the kit instruction manual. Chris conceded that (1) he hadn't taken enough photos of the original build, and (2) the design had changed significantly enough from his own build to merit a new build anyway, so the manual is representative of the final product.

 

Yesterday, I received a large box with the final production parts, and also a second set of earlier parts, including PE sheets. The photos here are of the production parts, and I'll cobble together a dry fit of the bits later, to give you a very quick idea of how this goes together, before work starts proper.

 

This kit must've taken an age to produce with all the sheets of pear, plus the pear overlays and beautiful engraving too. Here's what you can roughly expect to see in a final production kit:

 

MDF

DSC_3884.jpg

 

DSC_3885.jpg

 

DSC_3886.jpg

 

 

 

Maple deck
DSC_3895.jpg

 

 

 

Ply parts

DSC_3888.jpg

 

DSC_3889.jpg

 

 

 

Pear parts

DSC_3890.jpg

 

DSC_3891.jpg

 

DSC_3892.jpg

 

DSC_3893.jpg

 

 

Other laser parts

DSC_3900.jpg

 

 

Strip wood

DSC_3894.jpg

 

 

 

Photo etch

DSC_3896.jpg

 

DSC_3897.jpg

 

DSC_3898.jpg

 

DSC_3899.jpg

 

 

Resin parts

DSC_3902.jpg

 

 

Fittings etc.

DSC_3903.jpg

 

DSC_3904.jpg

 

 

 

Rigging cord

DSC_3905.jpg

 

 

 

Acrylic display stand (with engraved name plates)

DSC_3907.jpg

 

 

It's interesting to see some of the design ideas, such as the stern/transom where the resin ornamentation sits atop the pear panel, and that panel has recesses engraved into it to allow the PE window frames to sit within!

 

I'll post a dry fit image of the hull a little later on...

Link to comment
Share on other sites

I’m really excited to watch your build of this. I thought it looked beautiful in Chris’s unveiling pictures and I can’t wait to see some of the new design ideas used.

Link to comment
Share on other sites

its going to be a lovely selling kit, Congratulations

Link to comment
Share on other sites

What a lovely kit again from Vanguard Models.

 

James, you did not post a picture of the finished model and I hope you do not mind me doing it: 

109632691_167224858182560_7316412506085390917_o.jpg.40ed8dfb0e8d06baa6c529dcaa5367f1.jpg

 

and for historical accuracy, the lady that inspired and gave her name to that beautiful vessel: 

 

138199344_220px-Chudleigh_Elizabeth.jpg.a3bbb4ca93324365a20a54ef6078b887.jpg

 

Now, how many hours have a day for you James? It seems that you are faster than FLASH and Superman re-united in your endeavor.

 

Yves

 

Link to comment
Share on other sites

I already have all production photo etched parts with me, and resin castings for stern decoration, figurehead, winch and other castings are on their way to me. All materials are with me, but will wait until I am sure all fits as it should before starting production laser cut parts.

 

A November release is anticipated.

 

I can tell you that designing the photo etched decoration took an absolute age...

logo.jpg
Vanguard Models on Facebook

Link to comment
Share on other sites

Time for an update.

 

Of course, these photos are part of the instruction manual, so I've taken a selection to show where I'm currently up to with DoK. There are three 3mm MDF sheets, and I took my time to remove all of them and clean the tabs up with a knife and/or sanding stick. All parts are engraved with a number, and I knew all would be used in this quick bench session. First up, I built the temporary cradle. There's a gorgeous acrylic one for final use, complete with engraved nameplate, so this one is the scrapper that I'll throw away at the end.

 

2.jpg

 

5.jpg

 

 

As the model is single deck and won't have the usefulness of another lower deck into which the masts can align, a simple part is slotted into the keel before any work starts. It's most accessible to add at this stage. The part is a nice, snug fit. This is the main mast position.

 

8.jpg

 

 

Before any bulkheads are fitted, I first mark a rough bevel line on the first and last three bulkheads and then grind this away with my Dremel. A number of other parts are also bevelled at this stage too, such as the outer cheek parts and the front of the inner longitudinal beams. All bulkheads are now slotted into place.

 

12.jpg

 

20.jpg

 

 

For the foremast, a couple of parts are added to the outer cheeks. These will create a round base into which the down will sit. These are then slotted into place.

17.jpg

 

21.jpg

 

 

Now, those longitudinal beams are now added, starting with the inner two...

23.jpg

 

25.jpg

 

 

...and followed by the outer two:

26.jpg

 

28.jpg

 

 

At this stage, I painted wood glue into the joints and left the whole lot for a few hours to cure. I prefer this method when there are so many slots and such perfect tolerances.

29.jpg

 

 

Construction of the stern gallery areas starts with slotting in three frames, easily recognised with their engraved position ID. These just slot straight into position as shown, and are then glued.

30.jpg

 

34.jpg

 

 

Four extra pieces are added just before and after the midships cabin area. These are to support the floor/deck at either side. The cabin floor is also fitted and clamped until set.

36.jpg

 

38.jpg

 

42.jpg

 

DSC_3998.jpg

 

 

Both the main and upper false decks are now glued into place. These are 0.8mm ply and you need to bend them and allow them to fit into the slots in the bulkhead tabs. This holds the deck parts remarkably flat across all bulkheads. As an insurance policy, I also add a couple of brass pins to the forward upper deck as there are no slots there to hold in position.

DSC_4011.jpg

 

 

One nice little touch are the temporary beams which now slot into the bulkhead tabs. These are to give everything some real rigidity whilst the hull is worked on from this point. Afterwards, the beams and tabs will be broken out and discarded.

DSC_4017.jpg

 

 

A few extra pieces at the stern, but not quite all. The model is now setting before I start to sand the hull to shape and add the ply bulwarks.

DSC_4019.jpg

 

 

More soon... 

 

Link to comment
Share on other sites

As an engineer, its great to see how Chris designs evolve over time and small new things are added making everything simplier. My Speedy from November almost feel out of date when i see some of the new solutions... haha.

Current builds: HMS Victory (Corel 1:98), HMS Snake (Caldercraft 1:64), HMBV Granado (Caldercraft 1:64), HMS Diana (Caldercraft 1:64), HMS Speedy (Vanguard Models 1:64) 

Link to comment
Share on other sites

2 hours ago, Vane said:

great to see how Chris designs evolve over time and small new things are added making everything simplier

I agree - the etched numbers and words on components make the kit even more foolproof. I think I'll have to add the Duchess to my Christmas wish list.

 

Cheers, Derek

 

Current build:   Duchess of Kingston

On hold:              HMS Winchelsea

 

Previous builds:  HMS SpeedyEnglish Pinnace, Royal Yacht Caroline (gallery),

                            Victory Cross-section (gallery), US Clipper Albatros, Red Dragon (years ago!)

 

On the stocks:    18th Century Longboat

Link to comment
Share on other sites

Yes, just a small thing like that... adding numbers/instructions on pieces. Saves us at least on hour of marking work and also makes the design more foolproof.

Current builds: HMS Victory (Corel 1:98), HMS Snake (Caldercraft 1:64), HMBV Granado (Caldercraft 1:64), HMS Diana (Caldercraft 1:64), HMS Speedy (Vanguard Models 1:64) 

Link to comment
Share on other sites

  • 2 weeks later...

Ok, I promised an update, and here we are. 

 

I've actually done far more than you see here because most of the deck fittings (bitts, cannon, coamings, steps etc.) are now built too. I'll show some of that work in the next update.

 

There are a LOT of photos in this update but they only represent a fraction of what will be included in the manual, as Chris has asked me to detail photo stuff much further than is normally done. The manual should be epic when done!

 

 

Ok, on with fairing the hull. This one, I found, much more straightforward to sand than Flirt. It certainly didn't take the same amount of time to get the results I wanted. Of course, a lime plank was used to test the flow of the hull with the sanding.

 

60.jpg

 

62.jpg

 

63.jpg

 

64.jpg

 

 

With the sanding done, the inner prow is fitted. This is cut from 3mm pearwood. The fit of this is positive and it slots without any ambiguity and is perfectly straight when added, but I still added a few clamps to the mix too.

66.jpg

 

67.jpg

 

 

The prow is added at this stage so that the 0.8mm ply bulwarks can plug into it and set the level for the whole length. This one is dead easy as the top of the bulwark should be more or less at the top of the bulkheads. Easy!  Oh, if you get worried about the usual inflexible ply and ripple at the bow, then you won't get it with this model. The ply doesn't go to deep, and the shape of the bow is much friendlier than some hulls.

70b.jpg

 

 

First planking is done with 1mm x 4mm lime, pinned as I go along with the very fine Amati pins that Chris supplies. The planks also tuck underneath the lower stern counter, so that's probably the trickiest area, but I didn't find it too bad for the first time I ever attempted doing it.

72a.jpg

 

72b.jpg

 

73a.jpg

 

74b.jpg

 

 

The inner keel is supplied in three further parts. These are self explanatory as you can see with the fore and aft parts. They will only plug into the hull in one position. The stern post is now sheathed in its outer pearwood facings (1mm thick) with laser engraving. This can now be glued to the model. Remember, apart from the sternpost facings, you won't see any of the other work...it'll all be covered over.

75a.jpg

 

75b.jpg

 

75c.jpg

 

76.jpg

 

77a.jpg

 

77b.jpg

 

77c.jpg

 

77d.jpg

 

The stern counter parts are now fitted and sanded. The lower pear is 1.5mm pear and I soaked that for 90 minutes and tightly bound it around a cylindrical 2kg weight and left it overnight to fully dry. The curve was perfect for the model.

79c.jpg

 

80c.jpg

 

 

More engraved pearwood now with the external bulwarks. It's vital that these are glued in exactly the right position, and the various holes adjacent to the windows and cannon ports, align with those in the ply bulwark. The bulwarks are first soaked and bent around the ply, then clamped and allowed to dry overnight. The dry parts are then glued to the model. Pear can swell quite a lot so you really do need to leave anything soaked, for an overnight drying session. 

81b.jpg

 

82.jpg

 

 

With the bulwarks in position the keel outer facings can be added. These create the rabbet for the planking, that Chris introduced with his Zulu and Fifie fishing boats. The parts are located with pear tabs and I also add brass pins thought the horseshoe to doubly align things.

84a.jpg

 

84b.jpg

 

84c.jpg

 

 

Second planking is done with 1mm x 4mm pear. I Managed to get three un-tapered planks in before tapering began. With this model, I only found the need to taper just one plank at the stern! As there is more real estate to cover there, I wasn't going to complain. All pear planking was done with Gorilla Glue CA gel.

85a.jpg

 

85b.jpg

 

 

Once the hull is sanded smooth, I marked a temporary waterline on the hull and many slight gaps below the waterline were filled with diluted acrylic filler, and all sanded smooth. Above the waterline, any gaps were pretty much either invisible or non-existent. 

86.jpg

 

87a.jpg

 

 

With the hull prepared, the temporary beams are removed, along with the bulkhead tabs. The remnants are sanded flush with the false deck. 

 

88a.jpg

 

88d.jpg

 

 

Before the maple deck is laid, the inner pear bulwarks are soaked and clamped around the inner ply bulwark and left overnight to dry. 

89b.jpg

 

 

A little edge sanding is needed to make sure these maple decks fit snugly. They are quite flexible, and they need to be to be able to get the parts into position due to the bulwarks that lean inwards. They are still nice and easy to fit though. Dilute white glue is applied to the maple deck sections and then they are stuck down, with clamps around the edges. 

90.jpg

 

92a.jpg

 

92b.jpg

 

 

Upper bulwarks now put in position. 

94b.jpg

 

 

Small oval MDF plugs are supplied to help align the main, inner bulwarks. With everything set, a sanding stick is used to level the tops of the bulwarks, even though they were very close anyhow. 

95a.jpg

 

 

I used my tiny set of tungsten carbide files to clean up inside the gun ports and the rail decor areas.

96a.jpg

 

96b.jpg

 

 

I'll post another update next week with more hull work and I'll show some deck fittings too.

 

More next time...

 

 

Link to comment
Share on other sites

This kit is definitely on my Christmas list! Chris's models seem to get more and more carefully designed and innovative. Thanks for the detailed log & pics.

 

Derek

Cheers, Derek

 

Current build:   Duchess of Kingston

On hold:              HMS Winchelsea

 

Previous builds:  HMS SpeedyEnglish Pinnace, Royal Yacht Caroline (gallery),

                            Victory Cross-section (gallery), US Clipper Albatros, Red Dragon (years ago!)

 

On the stocks:    18th Century Longboat

Link to comment
Share on other sites

This is one gorgeous looking ship!! Cant wait to see all the carving  on it!

Current builds;

 Henry Ramey Upcher 1:25

Providence whaleboat- 1:25     HMS Winchelsea 1764 1:48 

Completed:

HM Cutter Sherbourne- 1:64- finished    Triton cross section scratch- 1:60 - finished 

Non ship:  SBD-3 Dauntless 1:48 Hasegawa -FINISHED

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...