Jump to content

Chebece 1750 by Forlani daniel - FINISHED - 1:48

Recommended Posts

Ciao a tutti, 

Ho realizzato lo scaletto e sinceramente è stato abbastanza difficile essenzialmente per due motivi.
Il primo motivo: l'utilizzo della linea del ponte per realizzare la dima di pontuale per i riferimenti delle coste e la seconda dima per il cassero sovrapposta alla precedente.
Il secondo motivo: il disegno in pianta del ponte, questa misura non tiene conto del cavallino del ponte, quindi se avessi utilizzato questo disegno senza le dovute modifiche delle quote in lunghezza avrei ottenuto sulla dima di pontuale con una sagoma più corta di circa 5mm.

Alcune foto dello scaletto.
Se notate da una parte ho messo il disegno con la chiglia a pari e nell'altra foto si vede quanto il disegno è stato allungato.


Hi everyone, I realized the ladder and honestly it was quite difficult essentially for two reasons. The first reason: the use of the bridge line to create the pontic template for the rib references and the second template for the formwork overlapping the previous one. The second reason: the plan drawing of the bridge, this measure does not take into account the pony of the bridge, so if I had used this design without the due changes in the dimensions in length I would have obtained on the pontual template with a shorter shape of about 5mm. Some photos of the ladder. If you notice on one side I put the design with the keel on the same level and in the other photo you can see how long the design has been stretched



Dima di pontuale finita




Qui ho posizionato la dima del cassero



Un Salutone a presto

Link to comment
Share on other sites

Ciao a tutti, comincio a mettere alcune foto della carpenteria assiale.

Dritto di poppa con la continuazione della chiglia in un pezzo unico, ho ricavato questo particolare vicino ad un nodo per rispettare il più possibile in senso della venatura.


Hi everyone, I begin to put some photos of the axial carpentry. Straight aft with the continuation of the keel in a single piece, I obtained this detail near a knot to respect as much as possible in the direction of grain.


Thanks Dirk






Un Salutone

Link to comment
Share on other sites

Hello Dirk.

A nice start to a great build.

Looks like you have put a lot of thought into how you are going to build this model.

I've not seen anyone use a fly cutter for large curves for some years. Nice Machining of the timbers.


Regards Antony.


Ciao Dirk.

Un buon inizio per una grande build.

Sembra che tu abbia riflettuto molto su come costruire questo modello.

Non ho visto nessuno usare un cutter per grandi curve per alcuni anni. Bella lavorazione delle travi.


Saluti Antonio.

Best advice ever given to me."If you don't know ..Just ask.

Completed Mayflower

Completed Fun build Tail boat Tailboat

Completed Build Chinese Junk Chinese Pirate Junk

Completed scratch built Korean Turtle ship 1/32 Turtle ship

Completed Santa Lucia Sicilian Cargo Boat 1/30 scale Santa Lucia

On hold. Bounty Occre 1/45

Completed HMS Victory by DeAgostini modelspace. DeAgostini Victory Cross Section

Completed H.M.S. Victory X section by Coral. HMS Victory cross section

Completed The Black Pearl fun build Black Queen

Completed A large scale Victory cross section 1/36 Victory Cross Section

Link to comment
Share on other sites

  • 2 weeks later...

Hello and thanks to everyone,
Landrotten, I use only a manual milling machine, what you see in the photo is the FF 230 of Proxxon.


Altre foto:
Ho simulato il torello per vedere come si posizionava sulla chiglia


More photos:
I simulated the bull to see how it stood on the keel













Un Saluto

Link to comment
Share on other sites

Very Impressive work! I love to see how you work with the wood and tools and I thank you for the very instructive pictures.


Kind regards, Kees


ps. Dirk, any Dutch roots? Your name is very common in Holland

Link to comment
Share on other sites

Ciao e grazie a tutti, anche per gli auguri.

Hello and thank you all, also for your good wishes.

Yes, draw a line, then follow it during milling by moving the X-axis and W-axis together, trying to follow the curved line.














Un Saluto

Link to comment
Share on other sites

Ciao a tutti, ultime foto della carpenteria assiale, adesso passerò alla costruzione delle coste di spessore 2,8mm.


Hello to all, last photo of the axial carpentry, now I will pass to the construction of the coasts of thickness 2,8mm.










Siccome i disegni della monografia forniscono solo metà della costa ho dovuto con un programma vettoriale ricavare l'altra metà.


Since the drawings of the monograph provide only half of the coast I had to with a vector program get the other half.











Un Saluto

Link to comment
Share on other sites

Hi Daniel,


super progress and very neat work, wish you further all the best with this build.....



Current builds

-Lightship Elbe 1


- Steamship Ergenstrasse ex Laker Corsicana 1918- scale 1:87 scratchbuild

"Zeesboot"  heritage wooden fishing small craft around 1870, POB  clinker scratch build scale 1:24

Pilot Schooner # 5 ELBE  ex Wanderbird, scale 1:50 scratchbuild

Mississippi Sterwheelsteamer built as christmapresent for grandson modified kit build

Chebec "Eagle of Algier" 1753--scale 1:48-POB-(scratchbuild) 

"SS Kaiser Wilhelm der Grosse" four stacker passenger liner of 1897, blue ribbond awarded, 1:144 (scratchbuild)
"HMS Pegasus" , 16 gun sloop, Swan-Class 1776-1777 scale 1:64 from Amati plan 

-"Pamir" 4-mast barque, P-liner, 1:96  (scratchbuild)

-"Gorch Fock 2" German Navy cadet training 3-mast barque, 1:95 (scratchbuild) 

"Heinrich Kayser" heritage Merchant Steamship, 1:96 (scratchbuild)  original was my grandfathers ship

-"Bohuslän" , heritage ,live Swedish museum passenger steamer (Billings kit), 1:50 

"Lorbas", river tug, steam driven for RC, fictive design (scratchbuild), scale appr. 1:32

under restoration / restoration finished 

"Hjejlen" steam paddlewheeler, 1861, Billings Boats rare old kit, scale 1:50

Link to comment
Share on other sites

Great work Daniel, very symmetrical layout on the framing.





If at first you do not suceed, try, and then try again!
Current build: HMCSS Victoria (Scratch)

Next build: HMAS Vampire (3D printed resin, scratch 1:350)

Built:          Battle Station (Scratch) and HM Bark Endeavour 1768 (kit 1:64)

Link to comment
Share on other sites

Beautiful framing, Daniel.

"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               


Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         



Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Create New...