Jump to content
New Publication - Ship Modeler's Handbook - Temp Out of Stock again! ×

druxey

NRG Member
 View Profile  See their activity

  • Posts

    12,938

  • Joined

  • Last visited

 Content Type 

Everything posted by druxey

  1. druxey
    Thanks for this, Bruce!
  2. druxey
    Sweet!
  3. druxey
    The models may have omitted the rabbetted fashion piece as it is a pain to make (I know this from experience!) It involves a continuously changing rabbet angle on the fore side, and another for the transom planks aft. I'm sure that the real ships were fitted this way, as exposed end grain wood deteriorates rapidly when exposed.
  4. druxey
    ClipperFan: the usual underlay (again, for naval vessels) was tarred felt.
  5. druxey
    It appears that merchant practice in coppering (Muntz as you point out) differed from that used by the navy.
  6. druxey
    Feather out? Do you mean make gains until the planks are flush with each other into the rabbet? If so, that is the correct way it was done. Also, there was a rabbet in the fashion piece to protect the plank ends from rot.
  7. druxey
    It was common practice (in naval dockyards, at least) to launch, check for any leaky seams, drydock, seal, then copper the bottom. Otherwise it would be harder to detect the source of water ingress and a pain to remove the copper to caulk the offending seam(s.)
  8. druxey
    You will have as many varying opinions as replies here! I've used all the usual makes mentioned and they are all fine. However, for ease of cleaning and no easily damaged long needles, you might consider Aztek as an alternative.
  9. druxey
    Many happy hours sailing her, JD! Lovely looking hull.
  10. druxey
    Hmm. Gives new meaning to the expression 'knights errant'. Looking very good now.
  11. druxey
    Now you know the meaning of the word 'druxey': rotten to the core. It is a form of wood rot found in the shipyard: spongy white veins inside logs.
  12. druxey
    Yellow cedar might also be suitable for you.
  13. druxey
    Are you reeving the laniard in the correct direction or is your line not 'hardened'?
  14. druxey
    I always thought canaries were yellow, not salmon colored! (Another 'druxey correction')? Seriously, I'm very flattered.
  15. druxey
    We await the results of the Museum's findings!
  16. druxey
    Seems like using a sledgehammer to crack a nut. None of my masts and spars have seen a lathe. It is not difficult to start with square stock marked out (don't need a four jaw chuck!), cut it eight-square except fo the square sections, then round off the parts that need it, using strips of sandpaper back and forth until the 'flats' just disappear. You don't need a lathe with a long bed ($$$), 4 jaw chuck ($$), steady ($$), filing rest ($$) or other paraphernalia. Just pencil and rule, sharp chisel and sandpaper. There; I just saved you a ton of money!
  17. druxey
    Does look like rotating ball joints. I've not seen those before. It would be an advantage to point them down so any overflow would not go onto the deck.
  18. druxey
    Nicely done and welcome!
  19. druxey
    Superb work as usual, Gary. Shrek-like fingers? Watchmaker's tweezers are the answer.
  20. druxey
    The second layer for the spirketting is a kit simplification, as is the waterway and double planking as sketched by John.
  21. druxey
    Welcome. You are already well versed in modelmaking!
  22. druxey
    In the article the builder is Donald McCabe, not McKay!
  23. druxey
    Take or send these images either to National Museums Scotland or the British Museum.
  24. druxey
    Welcome to the Canuck contingent here!
  25. druxey
    Well, back on topic. It was a fun diversion, though! I'm sure that the full-length columns will be less likely to collapse than the originals, so perhaps it was a fortunate accident. Glad you could save the decorative painted part of the xylokastra. Stupid question: couldn't you find thread in the color you needed without having to make the witches' brew of dye?

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...