Jump to content

Bristol Pilot Cutter by michael mott - 1/8 scale - POF


Recommended Posts

Hellppppp! someone pick me up off the floor.  I am still stunned with the level of machining and manual skills you display here Michael.  Between you and KeithAug, a collation of your various works would make the best Video/Image based tutorial for us 'apprentices'.  That is some excellent work!

 

Thanks for taking the time to document your processes.  

 

cheers

 

Pat

If at first you do not suceed, try, and then try again!
Current build: HMCSS Victoria (Scratch)

Next build: HMAS Vampire (3D printed resin, scratch 1:350)

Built:          Battle Station (Scratch) and HM Bark Endeavour 1768 (kit 1:64)

Link to comment
Share on other sites

Thanks for all the nice comments and likes.

 

the oblong plate has now been attached to the lock body and the lock is now fitted to the door next is the handle.

when filing the hole for the slide plate (Latch) in order to be able to file just the right amount ie file only a particular amount away it occurred to me to use something of a known thickness as a guide. (The jaws on my Grinding vice are hard, not cutting tool hard but hard enough that they only need to be dressed occasionally.) I put the blade of the thickness gauge ont the jaw and pushed the piece to be filed down to the surface of the gauge with a flat block then tightened up the vice leaving just .008" to be filed down to the jaw. 

 

IMG_9008x1024.jpg.228584eb3a40a914c449fcaa782faa22.jpg

 

when filing the actual hole I used a different thickness the photograph was to show the principle.

 

After getting the plate shaped and drilled I set it up in the third hand to be soldered to the main plate of the lock.

 

IMG_9010x1024.jpg.cccf2cc6050126dcf15621e4b72ca141.jpg

 

Then rotated the set up over so that I could add the solder to the back side .

IMG_9009x1024.jpg.a37f8930c0233516185cbfb9584be973.jpg

a small sliver of solder placed with some cleaning type flux (duzall)

IMG_9012x1024.jpg.8eda79b7fff11528d7daac1f49425652.jpg

After heating with the air soldering gun rotated it back up and released

 

IMG_9014x1024.jpg.ab9f0446238be711b84229f1c01ca197.jpg

A couple more 00x90 screws to hold it into place.

 

I IMG_9020x1024.jpg.9ecad325c5f80a4d077b6d1c3e44024a.jpg

I have been thinking about the handle and I am leaning toward an oval shaped one not a lever, the oval feels a bit less harsh than the lever .

 

Michael

 

 

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Well, what can one say ... a lock-smith apprentice could have done this as his test-piece (in German we have a much more impressive word: Gesellenstück)

 

I understand that knobs are preferred on boats and ships over handles, as lines or clothing can easily get caught in handles - which kind of shows the pervasive maritime tradition in Britain, where doors usually have knobs.

 

wefalck

 

panta rhei - Everything is in flux

 

 

M-et-M-72.jpg  Banner-AKHS-72.jpg  Banner-AAMM-72.jpg  ImagoOrbis-72.jpg
Link to comment
Share on other sites

Michael,

 

Was way behind on your log, just caught up. All I can say absolutley a stunning work of art. What is more amazing is the metal work and machining that gives the cutter a soul.

Kudos.

John Allen

 

Current builds HMS Victory-Mamoli

On deck

USS Tecumseh, CSS Hunley scratch build, Double hull Polynesian canoe (Holakea) scratch build

 

Finished

Waka Taua Maori War Canoe, Armed Launch-Panart, Diligence English Revenue Cutter-Marine  Model Co. 


 

Link to comment
Share on other sites

Thanks again for the kind remarks, I settled on the oval handle I found a classic one that was for sale on Ebay so used that one as a guide  I liked the 2 inch square plate and the oval head screws. I set up the 1/2 inch collet in the square collet holder and made 4 cuts

 

Capture9021.JPG.ed2bf649101af1f48336320cc5bbeb47.JPG

Capture9023.JPG.941a7274b16514042688a892dabd4deb.JPG

 

The parted them off on the lathe

 

Capture9022.JPG.1bd84a1588dd880a951d611f23784465.JPG

Next I turned up a ball and filed the sides to create the oval shape it took a bit of fettling to get the correct shape. It occurred to me that it would be best to make the square key part integral to the handle so after shaping the handle I reduced the diameter so that it could be filed square.

 

Capture9027.JPG.8420cfc10de42ccdf16725a9d005c3e7.JPG

Slowly I filed down to the 1.2 mm to fit into the square hole in the lock, I used a bit of the same square tube as the gauge while filing to dimension.

 

Capture9030.JPG.7f19f83b4d25a00b7257c2d13b1a66f5.JPG  

then slid. the handle into the lock, just need to drill the screw holes in the plate and figure out the second handle for the back side of the door.

 

Capture9031.JPG.bd8ee9cb614754d9e6daf29b15928533.JPG

 

Capture9036.JPG.d55228de30b45c7ab588330d31c7c1fd.JPG

 

Michael

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Hi Michael,

 

Bravo.

 

I've never seen a square rose with an oval handle but the square looks good with the panelled door. I also admit to preferring unaligned screws, as you've done.

Link to comment
Share on other sites

Mark thanks this was the handle I followed.

 

Michael

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Greg, Druxey, Rick, Dirk, and Kurt, Thank you all for you kindness.

 

I have just about finished the handles now, The second Handle require a slightly different approach because I needed to insert the square tube into it. and I needed to do that under pressure so a tight fit. first the rough shaping.

IMG_9039x1024.jpg.38cb1b46add525d523b02ddbf802fac7.jpg

Then after getting the handle shaped the square tube was pushed into the hole.

 

IMG_9040x1024.jpg.3fb40f3aa3ef2b2403c7975817b1315d.jpg

 

Then cut off with the Jewelers saw.

 

IMG_9044x1024.jpg.3bbcc4b1b8cca62c129c4e0fed8485cc.jpg

I used the watchmakers key tool as a holder for the final polishing.

 

IMG_9045x1024.jpg.9060def78f219ec1fe1e010420448945.jpg

 

And the handles are done.

 

IMG_9046x1024.jpg.f036dab4702417da0010671a47682409.jpg

 

Next the square roses were drilled and countersunk IMG_9051x1024.jpg.ddb6599ba0a5ebfc771a398aa885383c.jpg

The fake screws are basically the same as the hinge screws except these are oval headed.

 

IMG_0690x1024.jpg.565dd96f2a20a401d25deedf0af12a9e.jpg

IMG_0688x1024.jpg.f83f0d7d6fadf31b69c622ad90026247.jpg

IMG_0693x1024.jpg.bbc3dedbab841ce1cd67a862a4f0e71b.jpg

and the back set mounted on the door as well, just four more screws.

 

IMG_0695x1024.jpg.6125839839b1cc6486f67da4acdcbd44.jpg

Time for a break today.

 

Michael

 

 

 

 

 

 

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Link to comment
Share on other sites

But where's the lock and key? ;) :)  Just kidding - darn that is some lovely work; you Sir are a magician with brass.

 

cheers

 

Pat

If at first you do not suceed, try, and then try again!
Current build: HMCSS Victoria (Scratch)

Next build: HMAS Vampire (3D printed resin, scratch 1:350)

Built:          Battle Station (Scratch) and HM Bark Endeavour 1768 (kit 1:64)

Link to comment
Share on other sites

I am about to hit the 'ignore this topic' button, it makes me ache ...

 

Brass and silver were traditionally given a thin coat of zapon-lacquer to prevent tarnishing.

 

On the other hand, it seems that the handles and taps on the SEA CLOUD were gold-plated, because it was cheaper this way to keep them bright.

 

Jewellery makers supply shops sell tampon-plating sets, in case you consider.

wefalck

 

panta rhei - Everything is in flux

 

 

M-et-M-72.jpg  Banner-AKHS-72.jpg  Banner-AAMM-72.jpg  ImagoOrbis-72.jpg
Link to comment
Share on other sites

Lovely work on the lock Michael - exquisite - only to be improved by making the end plate screw slots vertical.

Keith

 

Current Build:-

Cangarda (Steam Yacht) - Scale 1:24

 

Previous Builds:-

 

Schooner Germania (Nova) - Scale 1:36

https://modelshipworld.com/topic/19848-schooner-germania-nova-by-keithaug-scale-136-1908-2011/

Schooner Altair by KeithAug - Scale 1:32 - 1931

http://modelshipworld.com/index.php/topic/12515-schooner-altair-by-keithaug-scale-132-1931/?p=378702

J Class Endeavour by KeithAug - Amati - Scale 1:35 - 1989 after restoration.

http://modelshipworld.com/index.php/topic/10752-j-class-endeavour-by-keithaug-amati-scale-135-1989-after-restoration/?p=325029

 

Other Topics

Nautical Adventures

http://modelshipworld.com/index.php/topic/13727-nautical-adventures/?p=422846

 

 

Link to comment
Share on other sites

Steve, Pat, Bob, Geert, Eberhard, Keith and Johann thank you for you kind comments.

The front panel is now assembled and the catch plate is fitted. 

On 2/7/2020 at 12:39 PM, KeithAug said:

exquisite - only to be improved by making the end plate screw slots vertical.

I made sure the catch plate screw slots were vertical, the door will have to suffice with slanted screw slots. The tung oil really brings out the lustre of the inset panels and the ritch colour of the wood.

 

IMG_9106x1024.thumb.jpg.a016dc5d60abad3894b4c7c903ca6fdb.jpg

The bottom of the panel fits into a slot in the floorboards which are now scraped Maple, there is a 1/6th bar glued across the bottom of the panel that is level with the floorboards, this allows for the door to be contained within the panel and the click when it closes is audible

 

IMG_9107x1024.thumb.jpg.2888c0d795d6d5d5d8a7d62e57bdd6be.jpg

Next the rear panels to be glued up all the parts are cut already.  Once they are done then the side panels can be fitted as they will hook into the bulkheads at the forward and aft ends.

 

Michael

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Classic!  that looks really good Michael; the wood grain/figuring really brings it to life.

 

cheers

 

Pat

If at first you do not suceed, try, and then try again!
Current build: HMCSS Victoria (Scratch)

Next build: HMAS Vampire (3D printed resin, scratch 1:350)

Built:          Battle Station (Scratch) and HM Bark Endeavour 1768 (kit 1:64)

Link to comment
Share on other sites

Extremely nice work on the woodwork Michael.  As Pat has mentioned above, the grain really looks beautiful, especially now that the tung oil has been applied.  Matching the grain pattern down through the individual door panels is an elegant touch.  

 

Gary

Current Build   Pelican Eastern-Rig Dragger  

 

Completed Scratch Builds

Rangeley Guide Boat   New England Stonington Dragger   1940 Auto Repair Shop   Mack FK Shadowbox    

 

Link to comment
Share on other sites

  • 4 weeks later...

Eberhard and forum friends

I'm OK Family is OK Mind has been focused elsewhere at the moment.

One of my character flaws.

https://vimeo.com/manage/396847956/general

 

IMG_9360x1024.jpg.7d7fa3e1fb2aa761081da6b82884a47f.jpg

I am staying home keeping in touch with family by telephone and working in the workshop I needed a break from the woodwork and so have been attending my other passion the narrow gauge works locomotives. If anyone is interested i could do another thread in the non ship category model section.

 

Stay safe everyone, My hands have never been cleaner that they are right now in fact I have been needing to use some hand lotion because they are vry dry from all the washing.

 

Michael

 

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...