Jump to content

HIJMS Musashi by cog - plastic - Tamiya - 1:350 - old tool


Recommended Posts

Finally started on this big plastic tub. Besides the invisible PE from Tamiya - bring x-ray goggles - I've got both the Pontos detail up set advanced , and the FlyHawk. The latter is quite impressive. No pictures from the Pontos PE. I forgot to take pictures, and on top of that I just dropped my coolpix on the ground, lens first. It seems I might just as well buy a a new one, as repairs will cost me about the same :angry:

 

The Flyhawk had the Nagato booklet, but they sent me a replacement. It seems it is easier to find what parts go where with the proper booklet

 

Sister ship is built by Greg IJN Yamato 1:350

 

post-33-0-24832000-1483696302_thumb.jpgpost-33-0-62886900-1483696312_thumb.jpgpost-33-0-85986300-1483696323_thumb.jpg

post-33-0-58072400-1483696409_thumb.jpgpost-33-0-51785800-1483696429_thumb.jpgpost-33-0-62123000-1483696449_thumb.jpgpost-33-0-96900900-1483696468_thumb.jpgpost-33-0-03434000-1483696488_thumb.jpgpost-33-0-80913500-1483696507_thumb.jpg

 

This will be a slow (agonising) build. I've decided to start with all the small parts like guns and turrets to get some dexterity with the PE. This is worse than the stripdown Fokker DR1 I build from Eduard

post-33-0-74374500-1483697129_thumb.jpg

Edited by cog
Link to comment
Share on other sites

So far I've invested approximately 4 hours over the last few days in this build. I started with the main turrets ... still going on turret number 1

 

1st clean up the plastic base

post-33-0-55172800-1483697552_thumb.jpgpost-33-0-07133400-1483697544_thumb.jpg

 

2nd add the brass (1 piece of railing has not yet been glued, 2 pieces more to add)

post-33-0-20712700-1483697546_thumb.jpgpost-33-0-24611400-1483697548_thumb.jpgpost-33-0-20340400-1483697550_thumb.jpg

 

All the brass on top, and at the fore, are not in the Pontos set. So far it is just FlyHawk PE

 

Link to comment
Share on other sites

OMG Brasso!!!   I remember polishing my belt buckles with that stuff before every inspection.  The first few hours was the hardest on a new one to get the darned lacquer finish off the buckle and get to the brass.   I also remember worn out brass drain pipes that had been polished with Brasso from the late 1930's to the early 60's when the academy finally realized the cost to replace the piping was not worth the shine.   

 

Allan

Link to comment
Share on other sites

I guess we were ALL up early........I was up a 4:45 AM  :)    it's about time you got this off the ground..{in this case though....the keel laid}  :)   count me in on following your journey through the P.E. jungle.    promise.......I won't play with the shiny stuff  ;)

 

love that Fokker........looks real sweet  :)

Link to comment
Share on other sites

Keith,

You must have an alarm on new topics which are plastic models + PE!! Maybe no shares but then you must own a couple ;)

 

Good to see you Robin, I'll be looking for bottles ;)

 

Allan,

I'm not going to use Brasso, despite that hughe can from Robin.

 

Ken,

Don't make a mess, I would like to be able to find my dropped parts

 

Denis,

Thought you might like some twinkle stuff, great to have you aboard!

Edited by cog
Link to comment
Share on other sites

Cool to see more of these big PE-enhanced kit builds coming on MSW.  More and more I see of them, the closer I come to wanting to try one (the tiny PE parts must appeal to my masochistic side).  Good luck with the build, looking forward to the updates!

Link to comment
Share on other sites

Good to see you here Mike, Jan, OC, thanks for visiting

 

Some more pics. Pontos PE (Keith, got this set from Australia)
post-33-0-10093300-1483744863_thumb.jpgpost-33-0-17962700-1483744867_thumb.jpgpost-33-0-94367200-1483744871_thumb.jpgpost-33-0-03389900-1483744875_thumb.jpgpost-33-0-09274300-1483744878_thumb.jpgpost-33-0-80829100-1483744882_thumb.jpgpost-33-0-24221900-1483744887_thumb.jpg

 

Some reference material

post-33-0-10227400-1483744890_thumb.jpg

 

And the underside of the turret. At first I thought it were etched lines, looking more closely ... it's a mesh!!!

post-33-0-47310600-1483744893_thumb.jpg

 

Cheers

Link to comment
Share on other sites

Found your log this morning cog; sorry to be late to the show.  Looks like another very highly detailed model in the making here.  Those turret enhancements look great

 

Make room in the front row for me too please :)

 

cheers

 

Pat

Edited by BANYAN
Link to comment
Share on other sites

Good to see you here Mike, Jan, OC, thanks for visiting

 

Some more pics. Pontos PE (Keith, got this set from Australia)

pontos.1.jpg pontos.2.jpg pontos.3.jpg pontos.4.jpg pontos.5.jpg pontos.6.jpg pontos.7.jpg

 

Some reference material

t1b4.jpg

 

And the underside of the turret. At first I thought it were etched lines, looking more closely ... it's a mesh!!!

t1underside.jpg

 

Cheers

Link to comment
Share on other sites

Yesterday evening I tiled the top of the other two turrets. The first one I started from the wrong end. With the last two I went front to back, which made gluing a lot easier

post-33-0-60820500-1483807639_thumb.jpgpost-33-0-26602000-1483807815_thumb.jpg

 

This afternoon railings on turret two (darn, forgot the bottle Robin ;) )

post-33-0-54108000-1483807642_thumb.jpgpost-33-0-16722100-1483807644_thumb.jpgpost-33-0-70651800-1483807645_thumb.jpg

Edited by cog
Link to comment
Share on other sites

Jan,

 

I get them from different places. Have to take a look into my invoices... One of them is 30 years old, and comes from a stamp (the ones you put on letters) shop in Rotterdam. I like medical tweezers too. Most model building tweezers aren't very accurate or "stable"

Edited by cog
Link to comment
Share on other sites

Hi Carl,

Question on your tools: Where did you get your tweezers?

Mine have problems in keeping the points neatly centered opposite to each oher when I try to hold something small. (resulting in potential loss of parts, as they are launched into outer space....)

 

Jan

Jan

 

Have a look here: https://shop.drijfhoutnl.com/webwinkel-gereedschap/pincetten.html

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...